E6C3-C

Rugged Incremental 50-mm-dia. Rotary Encoder

E6C3-C

Rugged Rotary Encoder

Item list of E6C3-C

about this Product Family

Inquiry of this Product

last update: February 09, 2016

Model		E6C3-CWZ5GH	E6C3-CWZ3EH	E6C3-CWZ3XH
Power supply voltage		12 VDC -10% to 24 VDC +15%, ripple (p-p): 5% max.	5 VDC -5% to 12 VDC +10%, ripple (p-p): 5% max.
Current consumption *1		100 mA max.
Resolution (pulses/rotation)		100, 200, 300, 360, 500, 600, 720, 800, 1,000, 1,024, 1,200, 1,500, 1,800, 2,000, 2,048, 2,500, 3,600
Output phases		Phases A, B, and Z *5
Output configuration		Complementary outputs *2	Voltage output (NPN output)	Line driver output *3
Output capacity		Output voltage: VH = Vcc = 3 V min. (IO = 30 mA) VL = 2 V max. (IO = -30 mA) Output current: ±30 mA	Output resistance: 2 kΩ Output current: 35 mA max. Residual voltage: 0.7 V max.	AM26LS31 equivalent Output current: High level: IO = -10 mA Low level: IS = 10 mA Output voltage: VO = 2.5 V min. VS = 0.5 V max.
Maximum response frequency *4		125 kHz (65 kHz when using phase Z reset)
Phase difference between outputs		90°±45° between A and B (1/4 T ± 1/8 T)
Rise and fall times of output		1 μs max. (Cable length: 2 m, Output current: 30 mA)	1 μs max. (Cable length: 2 m, Output current: 35 mA)	1 μs max. (Cable length: 2 m, IO: -10 mA, IS: 10 mA)
Starting torque		10 mNm max. at room temperature, 30 mNm max. at low temperature
Moment of inertia		2.0 × 10^-6 kgm² max.; 1.9 × 10^-6 kgm² max. at 500 P/R max.
Shaft loading	Radial	80 N
Shaft loading	Thrust	50 N
Maximum permissible speed		5,000 r/min
Protection circuits		Output load short-circuit protection		---
Ambient temperature range		Operating: -10 to 70°C (with no icing), Storage: -25 to 85°C (with no icing)
Ambient humidity range		Operating/Storage: 35% to 85% (with no condensation)
Insulation resistance		20 MΩ min. (at 500 VDC) between current-carrying parts and case
Dielectric strength		500 VAC, 50/60 Hz for 1 min between current-carrying parts and case
Vibration resistance		Destruction: 10 to 500 Hz, 150 m/s² or 2-mm double amplitude for 11 min 3 times each in X, Y, and Z directions
Shock resistance		Destruction: 1,000 m/s² 3 times each in X, Y, and Z directions
Degree of protection		IEC 60529 IP65, in-house standards: oilproof
Connection method		Pre-wired Models (Standard cable length: 1 m)
Material		Case: Aluminum, Main unit: Aluminum, Shaft: SUS303
Weight (packed state)		Approx. 300 g
Accessories		Instruction manual Note: Coupling, mounting bracket and hex-head spanner are sold separately.

*1. An inrush current of approximately 9 A will flow for approximately 0.1 ms when the power is turned ON.
*2. Complementary Output
The complementary output has two output transistors (NPN and PNP) as shown below. These two output transistors
alternately turn ON and OFF depending on the high or low output signal. When using them, pull up to the positive
power supply voltage level or pull down to 0 V. The complementary output allows flow-in or flow-out of the output
current and thus the rising and falling speeds of signals are fast. This allows a long cable distance. They can be
connected to open-collector input devices (NPN, PNP).

*3. The line driver output is a data transmission circuit compatible with RS-422A and long-distance transmission is
possible with a twisted-pair cable. (AM26LS31 equivalent)
*4. The maximum electrical response speed is determined by the resolution and maximum response frequency as
follows:

This means that the Rotary Encoder will not operate electrically if its speed exceeds the maximum electrical
response speed.
*5. The phase Z signal is output when cut face D on the shaft and the cable connection direction are as shown in the
following diagram (output position range: ±15°).

last update: February 09, 2016

Product Category

Sensors
- Rotary Encoders
  - Incremental
    - E6A2-C
    - E6B2-C
    - E6C2-C
    - E6C3-C
    - E6D-C
    - E6F-C
    - E6H-C

Top of Page