Page top

Building Automation


Industrial Automation


Power Automation & Safety

Bangladesh Distributor

Primary Contents

Machine Automation Controllers

Model Ratings Temperature Humidity Vibration EMC Enclosure
NJ --- B B A B *
* There are no enclosure requirements for OMRON products. Follow the DNV enclosure requirements specified separately for installation locations of the panel containing the product.
Note 1: The above table lists series names. Ask your OMRON representative for details on specific model numbers.
Note 2: For type approvals, these models shall not be installed on the deck, in the bridge, or on machinery that has severe vibration conditions.
Note 3: Noise filter TAH-06-683 manufactured by Cosel Co., Ltd. or equivalent should be connected between the power terminals of NJ series and the power supply.
Type approval of the DNV (Det Norske Veritas) was made according to the Environmental Test Specific for Instrument and Automation Equipment Standard for Certification No. 2.4.
Refer to the following table for the location classes.
Table 2-1 Location classes-Selection guide
Column I Column II
Parameters Location within main area MAIN AREAS ON BOARD
Machinery spaces Control room, Accommodation Bridge Pump room, Holds, Rooms with no heating Open Deck
Temperature Inside cubicles, desks, etc. with temperature rise of 5°C or more B B B D D
All other locations A A A C D
Humidity Locations where special precau-tions are taken to avoid condensa-tion A A A A A
All other locations B B B B B
Vibration On machinery such as internal com-bustion engines, compressors, pumps, including piping on such machinery B --- --- B B
Masts --- --- --- --- C
All other locations A A A A A
EMC Electro-magnetic com-patibility All locations within specified main areas A A B A B
Enclosure Submerged application D --- --- D D
Below floor plates in engine room C --- --- --- ---
All other locations B A A B C

Programmable Controllers

Model Ratings Temperature Humidity Vibration EMC Enclosure
C200HW/C200HX/C200HG/C200HE --- A A A A *3
CJ1/CJ2 --- A B A A *3
CP1 --- B B A A *2 *3
CQM1H/CQM1 --- B A A A *3
CS1 --- B B A A *3
CVM1D/CV500/C500/C1000H --- B *1 B *1 A A *3
W4S1 --- B B A B *3
*1. The C1000H-APS01, however, is "A."
*2. Install inside a metal enclosure.
*3. There are no enclosure requirements for OMRON products. Follow the DNV enclosure requirements specified separately for installation locations of the panel containing the product.
Note 1: The above table lists series names. Ask your OMRON representative for details on specific model numbers.
Note 2: For type approvals, these models shall not be installed on the deck, in the bridge, or on machinery that has severe vibration conditions. Only W4S1 series can be installed on the bridge.
Note 3: The power for W4S1 series should be supplied from S8VS series manufactured by Omron or equivalent.
Type approval of the DNV (Det Norske Veritas) was made according to the Environmental Test Specific for Instrument and Automation Equipment Standard for Certification No. 2.4.
Refer to the following table for the location classes.
Table 2-1 Location classes-Selection guide
Column I Column II
Parameters Location within main area MAIN AREAS ON BOARD
Machinery spaces Control room, Accommodation Bridge Pump room, Holds, Rooms with no heating Open Deck
Temperature Inside cubicles, desks, etc. with temperature rise of 5°C or more B B B D D
All other locations A A A C D
Humidity Locations where special precau-tions are taken to avoid condensa-tion A A A A A
All other locations B B B B B
Vibration On machinery such as internal com-bustion engines, compressors, pumps, including piping on such machinery B --- --- B B
Masts --- --- --- --- C
All other locations A A A A A
EMC Electro-magnetic com-patibility All locations within specified main areas A A B A B
Enclosure Submerged application D --- --- D D
Below floor plates in engine room C --- --- --- ---
All other locations B A A B C

Networks

Model Ratings Temperature Humidity Vibration EMC Enclosure
GRT1 --- B B A A *
CS1W-CRM21 --- B B A A *
CJ1W-CRM21 --- B B A A *
CRS1-RPT01 --- B B A A *
* There are no enclosure requirements for OMRON products. Follow the DNV enclosure requirements specified separately for installation locations of the panel containing the product.
Note 1: The above table lists series names. Ask your OMRON representative for details on specific model numbers.
Note 2: For type approvals, these models shall not be installed on the deck, in the bridge, or on machinery that has severe vibration conditions.
Type approval of the DNV (Det Norske Veritas) was made according to the Environmental Test Specific for Instrument and Automation Equipment Standard for Certification No. 2.4.
Refer to the following table for the location classes.
Table 2-1 Location classes-Selection guide
Column I Column II
Parameters Location within main area MAIN AREAS ON BOARD
Machinery spaces Control room, Accommodation Bridge Pump room, Holds, Rooms with no heating Open Deck
Temperature Inside cubicles, desks, etc. with temperature rise of 5°C or more B B B D D
All other locations A A A C D
Humidity Locations where special precau-tions are taken to avoid condensa-tion A A A A A
All other locations B B B B B
Vibration On machinery such as internal com-bustion engines, compressors, pumps, including piping on such machinery B --- --- B B
Masts --- --- --- --- C
All other locations A A A A A
EMC Electro-magnetic com-patibility All locations within specified main areas A A B A B
Enclosure Submerged application D --- --- D D
Below floor plates in engine room C --- --- --- ---
All other locations B A A B C

Programmable Terminals

Model Ratings Temperature Humidity Vibration EMC Enclosure
NS5/NS8/NS10/NS12 --- A B A B A
NA5-7W/9W/12W/15W --- A B A B A
NA5-7U/9U/12U/15U --- A B A B A
Note 1: The above table lists series names. Ask your OMRON representative for details on specific model numbers.
Note 2: For type approvals, these models shall not be installed on the deck or on machinery that has severe vibration conditions.
Note 3: Noise filter TAH-06-683 manufactured by Cosel Co.,Ltd. Or FN-2080-XX manufactured by Schaffner or equivalent should be connected between terminals of
NA5-series and the power supply if NA5-series are installed on the bridge to assure EMC class"B".
Type approval of the DNV (Det Norske Veritas) was made according to the Environmental Test Specific for Instrument and Automation Equipment Standard for Certification No. 2.4.
Refer to the following table for the location classes.
Table 2-1 Location classes-Selection guide
Column I Column II
Parameters Location within main area MAIN AREAS ON BOARD
Machinery spaces Control room, Accommodation Bridge Pump room, Holds, Rooms with no heating Open Deck
Temperature Inside cubicles, desks, etc. with temperature rise of 5°C or more B B B D D
All other locations A A A C D
Humidity Locations where special precau-tions are taken to avoid condensa-tion A A A A A
All other locations B B B B B
Vibration On machinery such as internal com-bustion engines, compressors, pumps, including piping on such machinery B --- --- B B
Masts --- --- --- --- C
All other locations A A A A A
EMC Electro-magnetic com-patibility All locations within specified main areas A A B A B
Enclosure Submerged application D --- --- D D
Below floor plates in engine room C --- --- --- ---
All other locations B A A B C