Building Automation
Industrial Automation
Power Automation & Safety
Bangladesh Distributor
Question
Which Sockets and Hold-down Clips are for MY General-purpose Relays?
Answer
Refer to the following table.
Connecting Sockets/Hold-down Clips Reference Table
| Type | Front-mounting Socket | ||
| DIN track or screw mounting | Screw mounting only | ||
| Without terminal cover | With terminal cover | Without terminal cover | |
| Size of screw terminals: M3 | Size of screw terminals: M3.5 | ||
| MY2 MY2N MY2-D MY2N-D2 MY2-CR *3 MY2N-CR *3 | PYF08A (PYC-A1) | PYF08A-E (PYC-A1) | PYF08M (PYC-P) |
| MY3 MY3N MY3-D MY3N-D2 | PYF11A (PYC-A1) | --- | --- |
| MY4 MY4N MY4-D MY4N-D2 MY4-CR *3 MY4N-CR *3 | Size of screw terminals: M3 | --- | |
| PYF14A (PYC-A1) | PYF14A-E (PYC-A1) | ||
| Size of screw terminals: M3.5 | |||
| PYF14T (PYC-A1) | |||
| Type | Back-mounting Socket | ||||||
| Soider terminals | Wire-wrap terminals | PCB terminals | |||||
| Without clip | With clip | Without clip | With clip | ||||
| Size of screw terminals: M3.5 | Terminal length: 25 mm | Terminal length: 20 mm | Terminal length: 25 mm | Terminal length: 20 mm | |||
| MY2 MY2N MY2-D MY2N-D2 MY2-CR *3 MY2N-CR *3 | PY08 (PYC-P) | PY08-Y1 | PY08QN (PYC-P) | PY08QN2 (PYC-P) | PY08QN-Y1 | PY08QN2-Y1 | PY08-02 (PYC-P) |
| MY3 MY3N MY3-D MY3N-D2 | PY11 (PYC-P) | PY11-Y1 | PY11QN (PYC-P) | PY11QN2 (PYC-P) | PY11QN-Y1 | PY11QN2-Y1 | PY11-02 (PYC-P) |
| MY4 MY4N MY4-D MY4N-D2 MY4-CR *3 MY4N-CR *3 | PY14 (PYC-P) | PY14-Y1 | PY14QN (PYC-P) | PY14QN2 (PYC-P) | PY14QN-Y1 | PY14QN2-Y1 | PY1-02 (PYC-P) |
*1.Models indicated in parentheses are for the Hold-down Clips. Hold-down Clips are sold as two pieces per set, except for PCY-P, where only one Clip is included per set.
*2.PYF[]A-E models have terminal covers (finger protection). Round crimp terminals cannot be used for these models. Use forked crimp terminals.
*3.The Hold-down Clips are suitable for Relays that are smaller than 36 mm in height. Relays that are taller than 53 mm must be used with Y92H-3 or PYC-1 Back-mounting Sockets. (Y92H-3 is sold as two pieces per set, and PYC-1 as one piece per set.)
Note:Use the Surface-mounting Sockets (i.e., models with finger protection) with "-E" at the end of the model number. When using PF083A and PF113A, be sure not to exceed Sockets’ maximum carry current of 5 A. Using at a current exceeding 5 A may lead to burning. Round crimp terminals cannot be used for models with finger protection. Use forked crimp terminals.
Recommended Products
MY
New Latching Levers for Circuit Checking Added to Our Best-selling MY General-purpose Relays
LY
Power-switching Compact General-purpose Relays
G3PE (Three-phase)
Compact, Slim-profile SSRs with Heat Sinks. Solid State Contactors for Three-phase Heaters Reduced Installation Work with DIN Track Mounting.
Other General Purpose Relays FAQ
-
The Relay does not operate even when voltage is applied. Why is this?
-
We were using G2R General Purpose Relay to turn a solenoid valve ON and OFF, and sparks at the contact damaged the relay after only about 3 months of use. What caused this, and what kind of countermeasure is there for it?
-
A Relay burned out. Why is this?
FAQ
Top of page