Page top

Building Automation


Industrial Automation


Power Automation & Safety

Bangladesh Distributor

E2E

Standard Proximity Sensor

E2E

Standard Sensors for Detecting Ferrous Metals under Standard Conditions

Item list of E2E

about this Product Family

Related Contents

last update: September 16, 2015

E2E-X[]D[] DC 2-Wire Models

Size M8 M12
Shielded Shielded Unshielded Shielded Unshielded
Model E2E-X2D[] E2E-X4MD[] E2E-X3D[] E2E-X8MD[]
Sensing distance 2 mm ±10% 4 mm ±10% 3 mm ±10% 8 mm ±10%
Set distance *1 0 to 1.6 mm 0 to 3.2 mm 0 to 2.4 mm 0 to 6.4 mm
Differential travel 15% max. of sensing distance 10% max. of sensing distance
Detectable object Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to
Engineering Data on Data Sheet.)
Standard sensing object Iron,
8 × 8 × 1 mm		 Iron,
20 × 20 × 1 mm		 Iron,
12 × 12 × 1 mm		 Iron,
30 × 30 × 1 mm
Response frequency *2 1.5 kHz 1 kHz 0.8 kHz
Power supply voltage
(operating voltage range)		 Standard Models: 12 to 24 VDC, ripple (p-p): 10% max. (10 to 30 VDC)
US Models and Connector Models Used as UL-certified Models:
12 to 24 VDC, ripple (p-p): 10% max. (The operating voltage range is also the same.) *3
Leakage current 0.8 mA max.
Control
output		 Load current 3 to 100 mA, Diagnostic output: 50 mA for -D1(5)S Models
Residual
voltage *4		 3 V max. (Load current: 100 mA, Cable length: 2 m, M1J-T Models only: 5 V max.)
Indicators D1 Models: Operation indicator (red) and setting indicator (green)
D2 Models: Operation indicator (red)
Operation mode
(with sensing object
approaching)		 D1 Models: NO
D2 Models: NC
Refer to the timing charts under I/O Circuit Diagrams on Data Sheet for details.
Diagnostic output delay 0.3 to 1 s
Protection circuits Surge suppressor, Load short-circuit protection (for control and diagnostic output)
Ambient temperature
range		 Operating: -25 to 70°C, Storage: -40 to 85°C (with no icing or condensation)
Ambient humidity range Operating/storage: 35% to 95% (with no condensation)
Temperature influence ±15% max. of sensing distance at 23°C
in the temperature range of -25 to 70°C		 ±10% max. of sensing distance at 23°C in
the temperature range of -25 to 70°C
Voltage influence ±1% max. of sensing distance at rated voltage in the rated voltage ±15% range
Insulation resistance 50 MΩ min. (at 500 VDC) between current-carrying parts and case
Dielectric strength 1000 VAC, 50/60 Hz for 1 minute between current carry parts and case
Vibration resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z
directions
Shock resistance Destruction: 500 m/s2 10 times each in X,
Y, and Z directions		 Destruction: 1,000 m/s2 10 times each in X,
Y, and Z directions
Degree of protection Pre-wired Models: IEC 60529 IP67, in-house standards: oil-resistant
Connector Models: IEC 60529 IP67
Connection method Pre-wired Models (Standard cable length: 2 m), Connector Models, or Pre-wired
Connector Models (Standard cable length: 0.3 m)
Weight
(packed
state)		 Pre-wired
Models		 Approx. 60 g Approx. 70 g
Pre-wired
Connector
Models		 --- Approx. 40 g
Connector
Models		 Approx. 15 g Approx. 25 g
Materi-
als		 Case Stainless steel (SUS303) Nickel-plated brass
Sensing surface PBT
Clamping nuts Nickel-plated brass
Toothed washer Zinc-plated iron
Accessories Instruction manual

Size M18 M30
Shielded Shielded Unshielded Shielded Unshielded
Model E2E-X7D[] E2E-X14MD[] E2E-X10D[] E2E-X20MD[]
Sensing distance 7 mm ±10% 14 mm ±10% 10 mm ±10% 20 mm ±10%
Set distance *1 0 to 5.6 mm 0 to 11.2 mm 0 to 8 mm 0 to 16 mm
Differential travel 10% max. of sensing distance
Detectable object Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to
Engineering Data on Data Sheet.)
Standard sensing object Iron,
18 × 18 × 1 mm		 Iron, 30 × 30 × 1 mm Iron,
54 × 54 × 1 mm
Response frequency *2 0.5 kHz 0.4 kHz 0.1 kHz
Power supply voltage
(operating voltage range)		 Standard Models: 12 to 24 VDC, ripple (p-p): 10% max. (10 to 30 VDC)
US Models and Connector Models Used as UL-certified Models:
12 to 24 VDC, ripple (p-p): 10% max. (The operating voltage range is also the same.) *3
Leakage current 0.8 mA max.
Control
output		 Load current 3 to 100 mA, Diagnostic output: 50 mA for -D1(5)S Models
Residual
voltage *4		 3 V max. (Load current: 100 mA, Cable length: 2 m, M1J-T Models only: 5 V max.)
Indicators D1 Models: Operation indicator (red) and setting indicator (green)
D2 Models: Operation indicator (red)
Operation mode
(with sensing object
approaching)		 D1 Models: NO
D2 Models: NC
Refer to the timing charts under I/O Circuit Diagrams on Data Sheet for details.
Diagnostic output delay 0.3 to 1 s
Protection circuits Surge suppressor, Load short-circuit protection (for control and diagnostic output)
Ambient temperature
range		 Operating: -25 to 70°C, Storage: -40 to 85°C (with no icing or condensation)
Ambient humidity range Operating/storage: 35% to 95% (with no condensation)
Temperature influence ±10% max. of sensing distance at 23°C in the temperature range of -25 to 70°C
Voltage influence ±1% max. of sensing distance at rated voltage in the rated voltage ±15% range
Insulation resistance 50 MΩ min. (at 500 VDC) between current-carrying parts and case
Dielectric strength 1000 VAC, 50/60 Hz for 1 minute between current carry parts and case
Vibration resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z
directions
Shock resistance Destruction: 1,000 m/s2 10 times each in X, Y, and Z directions
Degree of protection Pre-wired Models: IEC 60529 IP67, in-house standards: oil-resistant
Connector Models: IEC 60529 IP67
Connection method Pre-wired Models (Standard cable length: 2 m), Connector Models, or Pre-wired
Connector Models (Standard cable length: 0.3 m)
Weight
(packed
state)		 Pre-wired
Models		 Approx. 130 g Approx. 175 g
Pre-wired
Connector
Models		 Approx. 70 g Approx. 110 g
Connector
Models		 Approx. 40 g Approx. 90 g
Materi-
als		 Case Nickel-plated brass
Sensing surface PBT
Clamping nuts Nickel-plated brass
Toothed washer Zinc-plated iron
Accessories Instruction manual

*1. Use the E2E within the range in which the setting indicator (green LED) is ON (except D2 Models).
*2. The response frequency is an average value.
       Measurement conditions are as follows: standard sensing object, a distance of twice the standard sensing object,
       and a set distance of half the sensing distance.
*3. For the information on UL-certified connector models, refer to your OMRON website.
*4. The residual voltage of each M1J-T Model is 5 V. When connecting to a device, make sure that the device can
       withstand the residual voltage. (Refer to page 26 for details.)

E2E-X[]Y[] AC 2-Wire Models

Size M8 M12
Shielded Shielded Unshielded Shielded Unshielded
Model E2E-X1R5Y[] E2E-X2MY[] E2E-X2Y[] E2E-X5MY[]
Sensing distance 1.5 mm ±10% 2 mm ±10% 5 mm ±10%
Set distance 0 to 1.2 mm 0 to 1.6 mm 0 to 4 mm
Differential travel 10% max. of sensing distance
Detectable object Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to
Engineering Data on Data Sheet.)
Standard sensing object Iron,
8 × 8 × 1 mm		 Iron, 12 × 12 × 1 mm Iron,
15 × 15 × 1 mm
Response frequency 25 Hz
Power supply voltage
(operating voltage range) *1		 24 to 240 VAC (20 to 264 VAC), 50/60 Hz
Leakage current 1.7 mA max.
Control
output		 Load current *2 5 to 100 mA 5 to 200 mA
Residual voltage Refer to Engineering Data on Data Sheet.
Indicators Operation indicator (red)
Operation mode
(with sensing object
approaching)		 Y1 Models: NO
Y2 Models: NC
Refer to the timing charts under I/O Circuit Diagrams on Data Sheet for details.
Protection circuits Surge suppressor
Ambient temperature range
*1 *2		 Operating/Storage: -25 to 70°C
(with no icing or condensation)		 Operating/Storage: -40 to 85°C
(with no icing or condensation)
Ambient humidity range Operating/storage: 35% to 95% (with no condensation)
Temperature influence ±10% max. of sensing distance at 23°C
in the temperature range of -25 to 70°C		 ±15% max. of sensing distance at 23°C
in the temperature range of -40 to 85°C,
±10% max. of sensing distance at 23°C
in the temperature range of -25 to 70°C
Voltage influence ±1% max. of sensing distance at rated voltage in the rated voltage ±15% range
Insulation resistance 50 MΩ min. (at 500 VDC) between current-carrying parts and case
Dielectric strength 4,000 VAC (M8 Models: 2,000 VAC), 50/60 Hz for 1 min between current-carrying
parts and case
Vibration resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z
directions
Shock resistance Destruction: 500 m/s2 10 times each in
X, Y, and Z directions		 Destruction: 1,000 m/s2 10 times each
in X, Y, and Z directions
Degree of protection Pre-wired Models: IEC 60529 IP67, in-house standards: oil-resistant
Connector Models: IEC 60529 IP67
Connection method Pre-wired Models (Standard cable length: 2 m) and Connector Models
Weight
(packed
state)		 Pre-wired Models
Model		 Approx. 60 g Approx. 70 g
Connector Models Approx. 15 g Approx. 25 g
Materials Case Stainless steel (SUS303) Nickel-plated brass
Sensing surface PBT
Clamping nuts Nickel-plated brass
Toothed washer Zinc-plated iron
Accessories Instruction manual

Size M18 M30
Shielded Shielded Unshielded Shielded Unshielded
Model E2E-X5Y[] E2E-X10MY[] E2E-X10Y[] E2E-X18MY[]
Sensing distance 5 mm ±10% 10 mm ±10% 18 mm ±10%
Set distance 0 to 4 mm 0 to 8 mm 0 to 14 mm
Differential travel 10% max. of sensing distance
Detectable object Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to
Engineering Data on Data Sheet.)
Standard sensing object Iron,
18 × 18 × 1 mm		 Iron, 30 × 30 × 1 mm Iron,
54 × 54 × 1 mm
Response frequency 25 Hz
Power supply voltage
(operating voltage range) *1		 24 to 240 VAC (20 to 264 VAC), 50/60 Hz
Leakage current 1.7 mA max.
Control
output		 Load current *2 5 to 300 mA
Residual voltage Refer to Engineering Data on Data Sheet.
Indicators Operation indicator (red)
Operation mode
(with sensing object
approaching)		 Y1 Models: NO
Y2 Models: NC
Refer to the timing charts under I/O Circuit Diagrams on Data Sheet for details.
Protection circuits Surge suppressor
Ambient temperature range
*1 *2		 Operating/Storage: -40 to 85°C (with no icing or condensation)
Ambient humidity range Operating/storage: 35% to 95% (with no condensation)
Temperature influence ±15% max. of sensing distance at 23°C in the temperature range of -40 to 85°C,
±10% max. of sensing distance at 23°C in the temperature range of -25 to 70°C
Voltage influence ±1% max. of sensing distance at rated voltage in the rated voltage ±15% range
Insulation resistance 50 MΩ min. (at 500 VDC) between current-carrying parts and case
Dielectric strength 4,000 VAC (M8 Models: 2,000 VAC), 50/60 Hz for 1 min between current-carrying
parts and case
Vibration resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z
directions
Shock resistance Destruction: 1,000 m/s2 10 times each in X, Y, and Z directions
Degree of protection Pre-wired Models: IEC 60529 IP67, in-house standards: oil-resistant
Connector Models: IEC 60529 IP67
Connection method Pre-wired Models (Standard cable length: 2 m) and Connector Models
Weight
(packed
state)		 Pre-wired Models
Model		 Approx. 130 g Approx. 175 g
Connector Models Approx. 40 g Approx. 90 g
Materials Case Stainless steel (SUS303) Nickel-plated brass
Sensing surface PBT
Clamping nuts Nickel-plated brass
Toothed washer Zinc-plated iron
Accessories Instruction manual

*1. When supplying 24 VAC to any of the above models, make sure that the operating ambient temperature range is at
       least −25°C.
*2. When using an M18 or M30 Connector Model at an ambient temperature between 70 and 85°C, make sure that the
       Sensor has a control output (load current) of 5 to 200 mA max.

E2E-X[]T1 AC/DC 2-Wire Models

Size M12 M18 M30
Shielded Shielded
Model E2E-X3T1 E2E-X7T1 E2E-X10T1
Sensing distance 3 mm ±10% 7 mm ±10% 10 mm ±10%
Set distance 0 to 2.4 mm 0 to 5.6 mm 0 to 8 mm
Differential travel 10% max. of sensing distance
Detectable object Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to
Engineering Data on Data Sheet.)
Standard sensing object Iron, 12 × 12 × 1 mm Iron, 18 × 18 × 1 mm Iron, 30 × 30 × 1 mm
Response
frequency
*1		 DC 1 kHz 0.5 kHz 0.4 kHz
AC 25 Hz
Power supply voltage
(operating voltage range) *2		 24 to 240 VDC (20 to 264 VDC)
48 to 240 VAC (40 to 264 VAC)
Leakage current DC: 1 mA max.
AC: 2 mA max.
Control
output		 Load current 5 to 100 mA
Residual
voltage		 DC: 6 V max. (Load current: 100 mA, Cable length: 2 m)
AC: 10 V max. (Load current: 5 mA, Cable length: 2 m)
Indicators Operation indicator (red), Setting indicator (green)
Operation mode
(with sensing object
approaching)		 NO (Refer to the timing charts under I/O Circuit Diagrams on Data Sheet for details.)
Protection circuits Load short-circuit protection (20 to 40 VDC only), Surge suppressor
Ambient temperature range Operating: -25 to 70°C, Storage: -40 to 85°C (with no icing or condensation)
Ambient humidity range Operating/Storage: 35% to 95% (with no condensation)
Temperature influence ±10% max. of sensing distance at 23°C in the temperature range of -25 to 70°C
Voltage influence ±1% max. of sensing distance at rated voltage in the rated voltage ±15% range
Insulation resistance 50 MΩ min. (at 500 VDC) between current-carrying parts and case
Dielectric strength 4,000 VAC, 50/60 Hz for 1 minute between current-carrying parts and case
Vibration resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z
directions
Shock resistance Destruction: 1,000 m/s2 10 times each in X, Y, and Z directions
Degree of protection IEC 60529 IP67, in-house standards: oil-resistant
Connection method Pre-wired Models (Standard cable length: 2 m)
Weight (packed state) Approx. 80 g Approx. 140 g Approx. 190 g
Materials Case Nickel-plated brass
Sensing surface PBT
Clamping nuts Nickel-plated brass
Toothed washer Zinc-plated iron
Accessories Instruction manual

*1. The response frequency is an average value. Measurement conditions are as follows: standard sensing object, a
       distance of twice the standard sensing object, and a set distance of half the sensing distance.
*2. Power Supply Voltage Waveform:
       Use a sine wave for the power supply. Using a rectangular AC power supply may result in faulty reset.

E2E-X[]E[]/F[] DC 3-Wire Models

Size M8 M12
Shielded Shielded Unshielded Shielded Unshielded
Model E2E-X1R5E[]/F[] E2E-X2ME[]/F[] E2E-X2E[]/F[] E2E-X5ME[]/F[]
Sensing distance 1.5 mm ±10% 2 mm ±10% 5 mm ±10%
Set distance 0 to 1.2 mm 0 to 1.6 mm 0 to 4 mm
Differential travel 10% max. of sensing distance
Detectable object Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to
Engineering Data on Data Sheet.)
Standard sensing object Iron,
8 × 8 × 1 mm		 Iron, 12 × 12 × 1 mm Iron,
15 × 15 × 1 mm
Response frequency *1 2 kHz 0.8 kHz 1.5 kHz 0.4 kHz
Power supply voltage
(operating voltage range) *2		 12 to 24 VDC, ripple(p-p): 10% max. (10 to 30 VDC)
Connector Models Used as UL-certified Models: 12 to 24 VDC,
ripple (p-p): 10% max. (The operating voltage range is also the same.) *3
Current consumption 13 mA max.
Control
output		 Load current *2 200 mA max.
Residual voltage 2 V max. (Load current: 200 mA, Cable length: 2 m)
Indicators Operation indicator (red)
Operation mode
(with sensing object
approaching)		 E1/F1 Models: NO
E2/F2 Models: NC
Refer to the timing charts under I/O Circuit Diagrams on Data Sheet for details.
Protection circuits Load short-circuit protection, Surge suppressor, Reverse polarity protection
Ambient temperature range
*2		 Operating/Storage: -40 to 85°C (with no icing or condensation)
Ambient humidity range Operating/Storage: 35% to 95% (with no condensation)
Temperature influence ±15% max. of sensing distance at 23°C in the temperature range of -40 to 85°C
±10% max. of sensing distance at 23°C in the temperature range of -25 to 70°C
Voltage influence ±1% max. of sensing distance at rated voltage in the rated voltage ±15% range
Insulation resistance 50 MΩ min. (at 500 VDC) between current-carrying parts and case
Dielectric strength 1,000 VAC, 50/60 Hz for 1 minute between current carry parts and case
Vibration resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z
directions
Shock resistance Destruction: 500 m/s2 10 times each in
X, Y, and Z directions		 Destruction: 1,000 m/s2 10 times each
in X, Y, and Z directions
Degree of protection Pre-wired Models: IEC 60529 IP67, in-house standards: oil-resistant
Connector Models: IEC 60529 IP67
Connection method Pre-wired Models (Standard cable length: 2 m) and Connector Models
Weight
(packed
state)		 Pre-wired Models Approx. 65 g Approx. 75 g
Connector
Models		 Approx. 15 g Approx. 25 g
Materials Case Stainless steel (SUS303) Nickel-plated brass
Sensing surface PBT
Clamping nuts Nickel-plated brass
Toothed washer Zinc-plated iron
Accessories Instruction manual

Size M18 M30
Shielded Shielded Unshielded Shielded Unshielded
Model E2E-X5E[]/F[] E2E-X10ME[]/F[] E2E-X10E[]/F[] E2E-X18ME[]/F[]
Sensing distance 5 mm ±10% 10 mm ±10% 18 mm ±10%
Set distance 0 to 4 mm 0 to 8 mm 0 to 14 mm
Differential travel 10% max. of sensing distance
Detectable object Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to
Engineering Data on Data Sheet.)
Standard sensing object Iron,
18 × 18 × 1 mm		 Iron, 30 × 30 × 1 mm Iron,
54 × 54 × 1 mm
Response frequency *1 0.6 kHz 0.2 kHz 0.4 kHz 0.1 kHz
Power supply voltage
(operating voltage range) *2		 12 to 24 VDC, ripple(p-p): 10% max. (10 to 30 VDC)
Connector Models Used as UL-certified Models: 12 to 24 VDC,
ripple (p-p): 10% max. (The operating voltage range is also the same.) *3
Current consumption 13 mA max.
Control
output		 Load current *2 200 mA max.
Residual voltage 2 V max. (Load current: 200 mA, Cable length: 2 m)
Indicators Operation indicator (red)
Operation mode
(with sensing object
approaching)		 E1/F1 Models: NO
E2/F2 Models: NC
Refer to the timing charts under I/O Circuit Diagrams on Data Sheet for details.
Protection circuits Load short-circuit protection, Surge suppressor, Reverse polarity protection
Ambient temperature range
*2		 Operating/Storage: -40 to 85°C (with no icing or condensation)
Ambient humidity range Operating/Storage: 35% to 95% (with no condensation)
Temperature influence ±15% max. of sensing distance at 23°C in the temperature range of -40 to 85°C
±10% max. of sensing distance at 23°C in the temperature range of -25 to 70°C
Voltage influence ±1% max. of sensing distance at rated voltage in the rated voltage ±15% range
Insulation resistance 50 MΩ min. (at 500 VDC) between current-carrying parts and case
Dielectric strength 1,000 VAC, 50/60 Hz for 1 minute between current carry parts and case
Vibration resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z
directions
Shock resistance Destruction: 1,000 m/s2 10 times each in X, Y, and Z directions
Degree of protection Pre-wired Models: IEC 60529 IP67, in-house standards: oil-resistant
Connector Models: IEC 60529 IP67
Connection method Pre-wired Models (Standard cable length: 2 m) and Connector Models
Weight
(packed
state)		 Pre-wired Models Approx. 150 g Approx. 195 g
Connector
Models		 Approx. 40 g Approx. 90 g
Materials Case Nickel-plated brass
Sensing surface PBT
Clamping nuts Nickel-plated brass
Toothed washer Zinc-plated iron
Accessories Instruction manual

*1. The response frequency is an average value. Measurement conditions are as follows: standard sensing object, a
       distance of twice the standard sensing object, and a set distance of half the sensing distance.
*2. When using an M8 Model at an ambient temperature between 70 and 85°C, supply 10 to 30 VDC to the Sensor and
       make sure that the Sensor has a control output of 100 mA maximum.
*3. For the information on UL-certified connector models, refer to your OMRON website.

last update: September 16, 2015

Product Category

Site Information

© Copyright Kyoto Engineering & Automation Ltd. All Rights Reserved.