Page top

Building Automation


Industrial Automation


Power Automation & Safety

Bangladesh Distributor

CRT1B-[]D02JS(-1) / []D04JS(-1)

Bit Slave Units with Compact Connectors

CRT1B-[]D02JS(-1) / []D04JS(-1)

Bit slave of smallest class in industry Innovation in wiring for any type of machinery

about this Product Family

Basic Performance Specifications

Item Specification
Communications power supply voltage 14 to 26.4 VDC
I/O power supply voltage *1 20.4 to 26.4 VDC (24 VDC -15%/+10%)
Noise immunity Conforms to IEC 61000-4-4, 2 kV (power line).
Vibration resistance 10 to 60 Hz with double-amplitude of 0.7 mm, 60 to 150 Hz and 50 m/s2 in
X, Y, and Z directions for 80 min each
Shock resistance 150 m/s2 (3 times each in 6 directions on 3 axes)
Dielectric strength 500 VAC (between isolated circuits)
Insulation resistance 20 MΩ min. (between isolated circuits)
Ambient operating temperature -10 to 55°C
Ambient operating humidity 25% to 85% (with no condensation)
Ambient operating atmosphere No corrosive gases
Storage temperature -25 to 65°C
Storage humidity 25% to 85% (with no condensation)
Terminal block screw tightening
torque *2
M3 wiring screws: 0.5 Nm
M3 mounting screws: 0.5 Nm
Installation Mounted on 35-mm DIN Track or Mounting Bracket, or secured with M4
screws (depending on model)

*1. The I/O power supply is called the sensor power supply in information for the CRT1-VAD04S.
*2. Applicable only to Slaves to which screw terminal blocks are mounted.

Input Section Specifications

Item Specification
Model CRT1B-ID02JS CRT1B-ID02JS-1 CRT1B-ID04JS CRT1B-ID04JS-1
I/O capacity 2 inputs 4 inputs
Internal I/O common NPN PNP NPN PNP
ON voltage 10.5 VDC min.
(between each input
terminal and the V
terminal)
10.5 VDC min.
(between each input
terminal and the G
terminal)
10.5 VDC min.
(between each input
terminal and the V
terminal)
10.5 VDC min.
(between each input
terminal and the G
terminal)
OFF voltage --- --- --- ---
OFF current 1.0 mA max. 1.0 mA max.
Input current 3.0 mA min./input (at 10.5 VDC) 3.0 mA min./input (at 10.5 VDC)
Sensor power supply
voltage
Communications power supply voltage 0 V
(max.)
Communications power supply voltage -1 V
(min.)
Communications power supply voltage 0 V
(max.)
Communications power supply voltage -1 V
(min.)
ON delay 1.5 ms max. 1.5 ms max.
OFF delay 1.5 ms max. 1.5 ms max.
Number of circuits
per common
2 inputs/common 4 inputs/common
Power short-circuit
detection
Not supported. Not supported.
Isolation method No isolation No isolation
Input indicators LEDs (yellow) LEDs (yellow)
Degree of protection IEC standard IP20 IEC standard IP20
Installation M4 screw mounting using CRT1B-ATT03
Mounting Bracket
M4 screw mounting using CRT1B-ATT03
Mounting Bracket
Power supply type Network power supply Network power supply
Communications
power supply current
consumption *
25 mA max. for 24-VDC power supply voltage
30 mA max. for 14-VDC power supply voltage
35 mA max. for 24-VDC power supply voltage
40 mA max. for 14-VDC power supply voltage
Input device supply
current
50 mA/point
(G terminal)
50 mA/point
(V terminal)
50 mA/point
(G terminal)
50 mA/point
(V terminal)
Weight 16 g max. 21 g max.

* The current consumption is for Bit Slave Unit communications current when all inputs are OFF, i.e., it does not include
   input device current consumption. The communications power supply is also used for the I/O power supply for sensors.
   Be sure to consider the sensor current consumption and the number of sensors connected in addition to the
   communications power.
   The power supply current consumption is expressed by the following formula.
   Communications power supply current consumption = Bit Slave Unit communications current consumption + (Bit Slave
   Unit input current × number of inputs used) + (sensor current consumption × number of sensors used)

Output Section Specifications

Item Specification
Model CRT1B-OD02JS CRT1B-OD02JS-1 CRT1B-OD04JS CRT1B-OD04JS-1
I/O capacity 2 outputs 4 outputs
Internal I/O common NPN PNP NPN PNP
Rated output current 0.1 A/output 0.1 A/output
Load power supply
voltage
Communications power supply voltage 0 V
(max.)
Communications power supply voltage -1.2 V
(min.)
Communications power supply voltage 0 V
(max.)
Communications power supply voltage -1.2 V
(min.)
Residual voltage 1.2 V max. (0.1 A DC,
between each output
terminal and G
terminal)
1.2 V max. (0.1 A DC,
between each output
terminal and V
terminal)
1.2 V max. (0.1 A DC,
between each output
terminal and G
terminal)
1.2 V max. (0.1 A DC,
between each output
terminal and V
terminal)
Leakage current 0.1 mA max. 0.1 mA max.
ON delay 0.5 ms max. 0.5 ms max.
OFF delay 1.5 ms max. 1.5 ms max.
Number of circuits
per common
2 outputs/common 4 outputs/common
Load short-circuit
detection
Not supported. Not supported.
Isolation method No isolation No isolation
Output indicators LEDs (yellow) LEDs (yellow)
Degree of protection IEC standard IP20 IEC standard IP20
Installation M4 screw mounting using CRT1B-ATT03
Mounting Bracket
M4 screw mounting using CRT1B-ATT03
Mounting Bracket
Power supply type Network power supply Network power supply
Communications
power supply current
consumption *
25 mA max. for 24-VDC power supply voltage
30 mA max. for 14-VDC power supply voltage
30 mA max. for 24-VDC power supply voltage
35 mA max. for 14-VDC power supply voltage
Output device supply
current
30 mA/point
(G terminal)
30 mA/point
(V terminal)
30 mA/point
(G terminal)
30 mA/point
(V terminal)
Weight 16 g max. 21 g max.

* The current consumption is for Bit Slave Unit communications current when all outputs are OFF, i.e., it does not include
   the output device load current consumption.
   The communications power supply is also used for the I/O power supply for actuators. Be sure to consider the actuator
   load current consumption and the number of sensors connected in addition to the communications power. The power
   supply current consumption is expressed by the following formula.
   Communications power supply current consumption = Bit Slave Unit communications current consumption + (actual
   load current × number of actuators used)

Input and Output Section Specifications

1-point Input and 1-point Output units

Input Section Specification

Item Specification
Model CRT1B-MD02JS CRT1B-MD02JS-1
I/O capacity 1 input
Internal I/O common NPN PNP
ON voltage 10.5 VDC min. (between each input
terminal and the V terminal)
10.5 VDC min. (between each input
terminal and the G terminal)
OFF voltage --- ---
OFF current 1.0 mA max.
Input current 3.0 mA min./input (at 10.5 VDC)
Sensor power supply voltage Communications power supply voltage 0 V (max.)
Communications power supply voltage -1 V (min.)
ON delay 1.5 ms max.
OFF delay 1.5 ms max.
Number of circuits per common 1 input/common
Power short-circuit detection Not supported.
Isolation method No isolation
Input indicators LEDs (yellow)
Degree of protection IEC standard IP20
Installation M4 screw mounting using CRT1B-ATT03 Mounting Bracket
Power supply type Network power supply
Communications power supply
current consumption *
25 mA max. for 24-VDC power supply voltage
30 mA max. for 14-VDC power supply voltage
Input device supply current 50 mA/point (G terminal) 50 mA/point (V terminal)

* The current consumption is for Bit Slave Unit communications current when all inputs are OFF, i.e., it does not include
    input device current consumption. The communications power supply is also used for the I/O power supply for
    sensors. Be sure to consider the sensor current consumption and the number of sensors connected in addition to the
    communications power. The power supply current consumption is expressed by the following formula.
    Communications power supply current consumption = Bit Slave Unit communications current consumption + (Bit Slave
    Unit input current × number of inputs used) + (sensor current consumption × number of sensors used)

Output Section Specification

Item Specification
Model CRT1B-MD02JS CRT1B-MD02JS-1
I/O capacity 1 output
Internal I/O common NPN PNP
Rated output current 0.1 A/output
Load power supply voltage Communications power supply voltage 0 V (max.)
Communications power supply voltage -1.2 V (min.)
Residual voltage 1.2 V max. (DC, 0.1 A, between each
output terminal and G terminal)
1.2 V max. (DC, 0.1 A, between each
output terminal and V terminal)
Leakage current 0.1 mA max.
ON delay 0.5 ms max.
OFF delay 1.5 ms max.
Number of circuits per common 1 output/common
Load short-circuit detection Not supported.
Isolation method No isolation
Output indicators LEDs (yellow)
Degree of protection IEC standard IP20
Installation M4 screw mounting using CRT1B-ATT03 Mounting Bracket
Power supply type Network power supply
Output device supply current 30 mA/point (G terminal) 30 mA/point (V terminal)

2-points Inputs and 2-points Outputs units

Input Section Specification

Item Specification
Model CRT1B-MD04JS CRT1B-MD04JS-1
I/O capacity 2 inputs
Internal I/O common NPN PNP
ON voltage 10.5 VDC min. (between each input
terminal and the V terminal)
10.5 VDC min. (between each input
terminal and the G terminal)
OFF voltage --- ---
OFF current 1.0 mA max.
Input current 3.0 mA min./input (at 10.5 VDC)
Sensor power supply voltage Communications power supply voltage 0 V (max.)
Communications power supply voltage -1 V (min.)
ON delay 1.5 ms max.
OFF delay 1.5 ms max.
Number of circuits per common 2 inputs/common
Power short-circuit detection Not supported.
Isolation method No isolation
Input indicators LEDs (yellow)
Degree of protection IEC standard IP20
Installation M4 screw mounting using CRT1B-ATT03 Mounting Bracket
Power supply type Network power supply
Communications power supply
current consumption *
35 mA max. for 24-VDC power supply voltage
40 mA max. for 14-VDC power supply voltage
Input device supply current 50 mA/point (G terminal) 50 mA/point (V terminal)
Weight 21 g max.

* The current consumption is for Bit Slave Unit communications current when all inputs are OFF, i.e., it does not include
    input device current consumption. The communications power supply is also used for the I/O power supply for
    sensors. Be sure to consider the sensor current consumption and the number of sensors connected in addition to the
    communications power. The power supply current consumption is expressed by the following formula.
    Communications power supply current consumption = Bit Slave Unit communications current consumption + (Bit Slave
    Unit input current × number of inputs used) + (sensor current consumption × number of sensors used)

Output Section Specification

Item Specification
Model CRT1B-MD04JS CRT1B-MD04JS-1
I/O capacity 2 outputs
Internal I/O common NPN PNP
Rated output current 0.1 A/output
Load power supply voltage Communications power supply voltage 0 V (max.)
Communications power supply voltage -1.2 V (min.)
Residual voltage 1.2 V max. (DC, 0.1 A, between each
output terminal and G terminal)
1.2 V max. (DC, 0.1 A, between each
output terminal and V terminal)
Leakage current 0.1 mA max.
ON delay 0.5 ms max.
OFF delay 1.5 ms max.
Number of circuits per common 2 outputs/common
Load short-circuit detection Not supported.
Isolation method No isolation
Output indicators LEDs (yellow)
Degree of protection IEC standard IP20
Installation M4 screw mounting using CRT1B-ATT03 Mounting Bracket
Power supply type Network power supply
Output device supply current 30 mA/point (G terminal) 30 mA/point (V terminal)