Page top

Building Automation


Industrial Automation


Power Automation & Safety

Bangladesh Distributor

H3FA

Solid-state Timer

H3FA

DIP Model Timer for PC Board Use Provides Contact and Solid-state Output

about this Product Family

Time Ranges

Model Rated time Time setting range
H3FA-A 1 s 0.1 to 1 s
H3FA-AU 10 s 1 to 10 s
H3FA-SA 1 min 0.1 to 1 min
H3FA-SAU 10 min 1 to 10 min
H3FA-B 6 s 0.6 to 6 s
H3FA-BU 60 s 6 to 60 s
H3FA-SB 6 min 0.6 to 6 min
H3FA-SBU 60 min 6 to 60 min

Note: 1. The above timing ranges apply when the internal variable resistor of H3FA is used.
           2. The external variable resistor may also be used by opening the terminal connected to the internal variable
                resistor.
           3. Wire the appropriate terminal to select a time setting range. Refer to Rated Time and Terminal Connections on
                Data Sheet for details.

Ratings

Item H3FA-A/ H3FA-B
H3FA-AU/ H3FA-BU
H3FA-SA/ H3FA-SB
H3FA-SAU/ H3FA-SBU
Rated supply voltage 5 V DC, 6V DC, 12V DC, 24 V DC *1 5/6 V DC *1
12/24 V DC *1, *2
Operating voltage range 5 V DC: 90% to 110% of rated supply voltage
6, 12, 24 V DC: 85% to 110% of rated supply voltage
Power consumption 5, 6 V DC: approx. 230 mW
12 V DC: approx. 270 mW
24 V DC: approx. 330 mW
5/6 V DC: approx. 80 mW
12 V DC: approx. 100 mW
24 V DC: approx. 240 mW
Control outputs Contact output: SPST-NO + SPST-NC,
3 A at 250 V AC with resistive load,
Minimum applied load: 10 mA at 5 V DC
(Failure level: P, reference value)
Solid-state output: 150 mA max. at 30 V DC
Residual voltage: 1.0 V max.
Ambient temperature Operating: -10°C to 55°C (with no icing)
Storage: -25°C to 65°C (with no icing)
Ambient humidity 35% to 85%

H3FA Specifications 4

Characteristics

Accuracy of operating
time
±0.5% FS max. *1, *3
Setting error 0 to 30 % FS max. (at 20°C , at rated voltage)
Reset time 10 ms max.
Influence of voltage ±1% FS max. (2% FS max. for 5, 6, 5/6 V DC-operated models)
Influence of temperature ±5% FS max. *1
Insulation resistance 100 MΩ min. (at 500 V DC)
Dielectric strength 1,500 V AC, 50/60 Hz for 1 min (between control output and operating circuit) *2
1,000 V AC, 50/60 Hz for 1 min (between contacts not located next to each other) *2
Vibration resistance Destruction: 10 to 55 Hz with 0.375-mm single amplitude in 3 directions for 2 hour each
Malfunction: 10 to 55 Hz with 0.25-mm single amplitude in 3 directions for 10 minutes each
Shock resistance Destruction: 1,000 m/s2 3 times each in 6 directions on 3 axes
Malfunction: 100 m/s2 3 times each in 6 directions on 3 axes
Life expectancy Mechanical: 10,000,000 operations min. (under no load at 1,800 operations/h) *2
Electrical: 100,000 operations min. (3 A at 250 V AC, resistive load at 1,800 operations/h) *2
Approved safety
standards
UL508, CSA C22.2 No.14
Weight Contact output models: approx. 15 g
Solid-state output models: approx. 10 g

*1. Add or subtract 10 ms to the ratings when using a timer with a rated time of 1 s.
*2. Applicable to contact output models.
*3. This value assumes that the adjustment on the H3FA is used. (It does not apply if an externally connected resistor is
       used. For details, refer to External Resistors and Operating Time (Reference Value) on Data Sheet for details.)