E3X-DA-S Digital Fiber Amplifier Unit/Specifications | OMRON Bangladesh by Kyoto Engineering & Automation

Type		Standard models		Ultra-long-term APC models	High-speed response models
Type		Standard models	Model for Sensor Communications Unit	Ultra-long-term APC models	High-speed response models
Model		E3X-DA[]-S ([]: 21/51/7/9)	*E3X-DA0-S 1**	E3X-DA[]R-S ([]: 21/51/7/9)	E3X-DA[]F-S ([]: 21/51/7/9)
Light source (wavelength)		Red,4-element LED (625 nm)
Power supply voltage		12 to 24 VDC ± 10%, ripple (p-p) 10% max.	Supplied from the connector through the Sensor Communications Unit	12 to 24 VDC ±10%, ripple (p-p) 10% max.
Power consumption		Normal mode: 960 mW max. (Current consumption: 40 mA max. at 24 VDC, 80 mA max. at 12 VDC) Power saving ECO1: 720 mW max. (Current consumption: 30 mA max. at 24 VDC, 60 mA max. at 12 VDC) Power saving ECO2: 600 mW max. (Current consumption: 25 mA max. at 24 VDC, 50 mA max. at 12 VDC)
Control output/APC alarm output *1		Load power supply voltage: 26.4 VDC max.; NPN/PNP open collector; load current: 50 mA max.; residual voltage: 2 V max.
*External input 2**		No-voltage input (contact/transistor) *3	---	No-voltage input (contact/transistor) *3	---
Protection circuits		Power supply reverse polarity protection, output short-circuit protection and output reverse polarity protection
Re- sponse time	Super-high- speed Mode *4	Operate or reset: 80 μs	---	Operate or reset: 80 μs	NPN output: Operate: 46 μs, Reset: 48 μs PNP output: Operate: 51 μs, Reset: 53 μs
	High-speed Mode	Operate or reset: 250 μs			---
	Standard Mode	Operate or reset: 1 ms
	High-resolution Mode	Operate or reset: 4 ms
	Tough Mode	Operate or reset: 16 ms
Sensitivity setting		Teaching or manual method
Func- tions	Power tuning	Light emission power and reception gain, digital control method
	Differential detection	Switchable between Single-edge and Double-edge Detection Modes. Single edge: Set to 250 μs, 500 μs, 1 ms, 10 ms, or 100 ms. Double edge: Set to 500 μs, 1 ms, 2 ms, 20 ms, or 200 ms			---
	Automatic power control (APC)	Always enabled. High-speed control of emission current Wide-range APC for the E3X-DA[]R-S
	Timer	Select from timer disabled, OFF-delay, ON-delay, One-shot, or ON-delay + OFF-delay timer
	Timer	1 ms to 5 s (1 to 20 ms set in 1-ms increments, 20 to 200 ms set in 10-ms increments, 200 ms to 1 s set in 100-ms increments, and 1 to 5 s set in 1-s increments)
	ATC	Provided
	APC margin display	---		Provided	---
	Slow-motion display	---			Provided
	Zero reset	Negative values can be displayed. (Threshold value is shifted.)
	Resetting settings	Select from initial reset (factory defaults) or user reset (saved settings).
	Mutual interference prevention	Possible for up to 10 units *5			---
	*ECO Mode 6**	Select from OFF (digital display lit), ECO1 (digital display dimmed), and ECO2 (digital display OFF).
	External input setting *2	Select from teaching operations, power tuning, zero reset, emitter OFF, or ATC start.			---
	Output setting	Select from output for each channel, area output, or self-diagnosis.		---
Indicator		Operation indicator for channel 1 (orange) Operation indicator for channel 2 (orange)		Operation indicator for channel 1 (orange) APC alarm output indicator (orange)	Operation indicator for channel 1 (orange) Power tuning indicator (orange)
Digital display		Select from incident level + threshold or other 6 patterns (Refer to 6. Display switch on Catalog.)
Display orientation		Switching between normal/reversed display is possible.
Key lock		Key lock		Key lock/Easy key lock.
Ambient illumination (Receiver side)		Incandescent lamp: 10,000 lx max. Sunlight: 20,000 lx max.
Maximum connectable Units		16 (The ambient temperature specification depends on the number of connected units.) *7
Ambient temperature range		Operating: Groups of 1 to 2 Amplifiers: -25 to 55°C Groups of 3 to 10 Amplifiers: -25 to 50°C Groups of 11 to 16 Amplifiers: -25 to 45°C *8
Ambient temperature range		Storage: - 30 to 70 °C (with no icing or condensation)
Ambient humidity range		Operating and storage: 35% to 85% (with no condensation)
Insulation resistance		20 MΩ min. (at 500 VDC)
Dielectric strength		1,000 VAC at 50/60 Hz for 1 minute
Vibration resistance (Destruction)		10 to 55 Hz with a 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions	10 to 150 Hz with a 0.7-mm double amplitude for 80 min each in X, Y, and Z directions	10 to 55 Hz with a 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
Shock resistance (Destruction)		500 m/s² for 3 times each in X, Y, and Z directions	200 m/s² for 3 times each in X, Y, and Z directions	500 m/s² for 3 times each in X, Y, and Z directions
Degree of protection		IEC 60529 IP50 (with Protective Cover attached)
Connection method		Pre-wired (standard cable length: 2 m) or wire-saving connector	Connector for Sensor Communications Unit	Pre-wired (standard cable length: 2 m) or wire-saving connector
Weight (packed state)		Pre-wired Models: Approx. 100 g, Wire- saving Connector Models: Approx. 55 g	Approx. 55 g	Pre-wired Models: Approx. 100 g, Wire- saving Connector Models: Approx. 55 g
Mate- rials	Case	Polybutylene terephthalate (PBT)
Mate- rials	Cover	Polycarbonate (PC)
Accessories		Instruction Manual

*1. The E3X-DA0-S Amplifier Unit allows you to use an E3X-ECT EtherCAT Sensor Communications Unit or E3X-CRT
CompoNet Sensor Communications Unit.
*2. Only for Pre-wired models.
*3. The following details apply to inputs.

	Contact input (relay or switch)	Non-contact input (transistor)
NPN	ON: Shorted to 0 V (sourcing current: 1 mA max.). OFF: Open or shorted to Vcc.	ON: 1.5 V max. (sourcing current: 1 mA max.) OFF: Vcc - 1.5 V to Vcc (leakage current: 0.1 mA max.)
PNP	ON: Shorted to Vcc (sinking current: 3 mA max.). OFF: Open or shorted to 0 V.	ON: Vcc - 1.5 V to Vcc (sinking current: 3 mA max.) OFF: 1.5 V max. (leakage current: 0.1 mA max.)

*4. The communications function and mutual interference prevention function are disabled if the detection mode is set to
Super-high-speed mode.
*5. Mutual interference prevention is enabled if Fiber Amplifier Units are connected together. It is also enabled in the
same way if E3X-DA-S-series Units and E3C-LDA-series Units are used together. If power tuning is enabled, mutual
interference prevention can be used for up to six units.
*6. For the standard models E3X-DA[]-S ([]: 21/51/7/9/0), the rated sensing distance is approximately 1/2 and the
incident level is approximately 1/3 of the normal levels when ECO mode is enabled.
*7. The maximum number of connectable Units is 30 when the E3X-ECT is used with the E3X-DA0-S.
*8. The following temperature ranges apply for operation when an E3X-ECT or E3X-CRT Sensor Communications Unit is
used with the E3X-DA0-S: Groups of 1 or 2 Amplifier Units: 0 to 55°C, Groups of 3 to 10 Amplifier Units: 0 to 50°C,
Groups of 11 to 16 Amplifier Units: 0 to 45°C, Groups of 17 to 30 Amplifier Units (with the E3X-ECT): 0 to 40°C.

Model		E3X-CN21/22/11	E3X-CN12
Rated current		2.5 A
Rated voltage		50 V
Contact resistance		20 mΩ max. (20 mVDC max., 100 mA max.) (The figure is for connection to the Fiber Amplifier Unit and the adjacent connector. It does not include the conductor resistance of the cable.)
No. of insertions		Destruction: 50 times (The figure for the number of insertions is for connection to the Fiber Amplifier Unit and the adjacent connector.)
Materials	Housing	Polybutylene terephthalate (PBT)
Materials	Contacts	Phosphor bronze/gold-plated nickel
Weight (packed state)		Approx. 55 g	Approx. 25 g

Note: The High-speed Mode cannot be used with the E3X-DA0-S.

Sensing method	Sensing direction	Size	Model	Sensing distance (mm)
Sensing method	Sensing direction	Size	Model	Tough mode	High- resolution mode	Standard mode	High- speed mode	Super- high-speed mode
Through-beam	Right-angle	M4	E32-T11N 2M	2,000	1,400	1,000	700	280
	Right-angle		E32-LT11N 2M	4,000 *	4,000 *	3,500	2,300	920
	Straight		E32-T11R 2M	2,000	1,400	1,000	700	280
			E32-LT11 2M	4,000 *	4,000 *	4,000 *	2,700	1,080
			E32-LT11R 2M	4,000 *	4,000 *	3,500	2,300	920
Reflective	Right-angle	M3	E32-C31N 2M	110	80	50	46	14
		M3	E32-C21N 2M	290	150	130	90	39
		M4	E32-D21N 2M	840	600	350	240	100
		M6	E32-C11N 2M	780	560	350	320	100
		M6	E32-LD11N 2M	840	600	350	240	100
	Straight	M3	E32-D21R 2M	140	100	60	40	16
			E32-C31 2M	330	240	150	100	44
			E32-C31M 1M	330	240	150	100	44
		M4	E32-D211R 2M	140	100	60	40	16
		M6	E32-D11R 2M	840	600	350	240	100
			E32-CC200 2M	1,400	1,000	600	400	180
			E32-LD11 2M	860	610	360	250	110
			E32-LD11R 2M	840	600	350	240	100

* The fiber length is 2 m on each side, so the sensing distance is given as 4,000 mm.

Sensing method	Size	Sensing direction	Model	Sensing distance (mm)
Sensing method	Size	Sensing direction	Model	Tough mode	High- resolution mode	Standard mode	High- speed mode	Super- high- speed mode
Through-beam	1 dia.	Top-view	E32-T223R 2M	450	300	250	150	60
	1.5 dia.		E32-T22B 2M	680	480	400	220	90
	3 dia.		E32-T12R 2M	2,000	1,400	1,000	700	280
	3 dia.	Side-view	E32-T14LR 2M	750	550	450	260	100
Reflective	1.5 dia.	Top-view	E32-D22B 2M	140	100	60	40	16
	1.5 dia. + 0.5 dia.		E32-D43M 1M	28	20	12	8	4
	3 dia.		E32-D22R 2M	140	100	60	40	16
			E32-D221B 2M	300	220	140	90	40
			E32-D32L 2M	700	500	300	200	90
	3 dia. + 0.8 dia.		E32-D33 2M	70	50	30	20	8

Sensing method	Sensing direction	Model	Sensing distance (mm)
Sensing method	Sensing direction	Model	Tough mode	High- resolution mode	Standard mode	High- speed mode	Super- high-speed mode
Through-beam	Top-view	E32-T15XR 2M	2,000	1,400	1,000	700	280
	Side-view	E32-T15YR 2M	750	550	450	260	100
	Flat-view	E32-T15ZR 2M	750	550	450	260	100
Reflective	Top-view	E32-D15XR 2M	840	600	350	240	100
	Side-view	E32-D15YR 2M	200	140	100	52	24
	Flat-view	E32-D15ZR 2M	200	140	100	52	24

Sensing method	Sensing direction	Model	Sensing distance (mm)
Sensing method	Sensing direction	Model	Tough mode	High- resolution mode	Standard mode	High- speed mode	Super- high- speed mode
Through-beam	Side-view	E32-T24R 2M	170	120	100	50	20
	Side-view	E32-T24E 2M	450	300	250	150	60
	Top-view	E32-T21-S1 2M	510	360	300	170	68
		E32-T33 1M	150	110	90	50	20
		E32-TC200BR 2M	2,000	1,400	1,000	700	280
Reflective	Side-view	E32-D24R 2M	70	52	30	20	8
	Side-view	E32-D24-S2 2M	120	80	53	45	14
	Top-view	E32-D43M 1M	28	20	12	8	4
		E32-D331 2M	14	10	6	4	2
		E32-D33 2M	70	50	30	20	8
		E32-D32-S1 0.5M	63	43	27	18	7
		E32-D31-S1 0.5M	63	43	27	18	7
		E32-DC200F4R 2M	140	100	60	40	16
		E32-D22-S1 2M	250	170	110	72	30
		E32-D21-S3 2M	250	170	110	72	30
		E32-DC200BR 2M	840	600	350	240	100
		E32-D25-S3 2M	250	170	110	72	30

Type	Spot diameter	Center distance (mm)	Model	Sensing distance (mm)
Type	Spot diameter	Center distance (mm)	Model	Tough mode	High- resolution mode	Standard mode	High- speed mode	Super- high- speed mode
Variable spot	0.1 to 0.6 dia.	6 to 5	E32-C42 1M + E39-F3A	Spot diameter of 0.1 to 0.6 mm at 6 to 15 mm.
Variable spot	0.3 to 1.6 dia.	10 to 30	E32-C42 1M + E39-F17	Spot diameter of 0.3 to 1.6 mm at 10 to 30 mm.
Parallel light	4 dia.	0 to 20	E32-C31 2M + E39-F3C	Spot diameter of 4 mm max. at 0 to 20 mm.
Parallel light	4 dia.	0 to 20	E32-C31N 2M + E39-F3C	Spot diameter of 4 mm max. at 0 to 20 mm.
Integrated lens	0.1 dia.	5	E32-C42S 1M	Spot diameter of 0.1 mm at 5 mm.
Integrated lens	6 dia.	50	E32-L15 2M	Spot diameter of 6 mm at 50 mm.
Small- spot	0.1 dia.	7	E32-C41 1M + E39-F3A-5	Spot diameter of 0.1 mm at 7 mm.
	0.5 dia.		E32-C31 2M + E39-F3A-5	Spot diameter of 0.5 mm at 7 mm.
	0.5 dia.		E32-C31N 2M + E39-F3A-5	Spot diameter of 0.5 mm at 7 mm.
	0.2 dia.	17	E32-C41 1M + E39-F3B	Spot diameter of 0.2 mm at 17 mm.
	0.5 dia.		E32-C31 2M + E39-F3B	Spot diameter of 0.5 mm at 17 mm.
	0.5 dia.		E32-C31N 2M + E39-F3B	Spot diameter of 0.5 mm at 17 mm.
	3 dia.	50	E32-CC200 2M + E39-F18	Spot diameter of 3 mm at 50 mm.
	3 dia.	50	E32-C11N 2M + E39-F18	Spot diameter of 3 mm at 50 mm.

Type	Sensing direction	Aper- ture angle	Model	Sensing distance (mm)
Type	Sensing direction	Aper- ture angle	Model	Tough mode	High- resolution mode	Standard mode	High- speed mode	Super- high- speed mode
Through-beam Integrated lens	Right-angle	15 °	E32-LT11N 2M	4,000 *2	4,000 *2	3,500	2,300	920
	Top-view	10 °	E32-T17L 10M	20,000 *1	20,000 *1	20,000 *1	20,000 *1	8,000
		15 °	E32-LT11 2M	4,000 *2	4,000 *2	4,000 *2	2,700	1,080
		15 °	E32-LT11R 2M	4,000 *2	4,000 *2	3,500	2,300	920
	Side-view	30 °	E32-T14 2M	4,000 *2	4,000 *2	4,000 *2	4,000 *2	1,800
Through- beam models with lenses	Right-angle	12 °	E32-T11N 2M + E39-F1	4,000 *2	4,000 *2	4,000 *2	4,000 *2	2,000
	Right-angle	6 °	E32-T11N 2M + E39-F16	4,000 *2	4,000 *2	4,000 *2	4,000 *2	3,600
	Top-view	12 °	E32-T11R 2M + E39-F1	4,000 *2	4,000 *2	4,000 *2	4,000*2	2,000
	Top-view	6 °	E32-T11R 2M + E39-F16	4,000 *2	4,000 *2	4,000 *2	4,000 *2	3,600
	Side-view	60 °	E32-T11R 2M + E39-F2	1,450	1,040	800	500	200
	Top-view	12 °	E32-T11 2M + E39-F1	4,000 *2	4,000 *2	4,000 *2	4,000 *2	1,860
	Top-view	6 °	E32-T11 2M + E39-F16	4,000 *2	4,000 *2	4,000 *2	4,000 *2	4,000 *2
	Side-view	60 °	E32-T11 2M + E39-F2	2,300	1,640	1,320	860	320
	Top-view	12 °	E32-T51R 2M + E39-F1	4,000 *2	4,000 *2	4,000 *2	3,900	1,500
	Top-view	6 °	E32-T51R 2M + E39-F16	4,000 *2	4,000 *2	4,000 *2	4,000 *2	4,000 *2
	Side-view	60 °	E32-T51R 2M + E39-F2	1,400	1,000	720	500	200
	Top-view	12 °	E32-T81R-S 2M + E39-F1	4,000 *2	4,000 *2	4,000 *2	2,700	1,000
	Top-view	6 °	E32-T81R-S 2M + E39-F16	4,000 *2	4,000 *2	4,000 *2	4,000 *2	1,800
	Side-view	60 °	E32-T81R-S 2M + E39-F2	1,000	720	550	360	140
	Top-view	12 °	E32-T61-S 2M + E39-F1	4,000 *2	4,000 *2	4,000 *2	4,000 *2	1,800
	Top-view	6 °	E32-T61-S 2M + E39-F16	4,000 *2	4,000 *2	4,000 *2	4,000 *2	3,100
	Side-view	60 °	E32-T61-S 2M + E39-F2	1,680	1,200	900	600	240
	Top-view	12 °	E32-T51 2M + E39-F1-33	4,000 *2	4,000 *2	4,000 *2	2,300	1,400
	Top-view	6 °	E32-T51 2M + E39-F16	4,000 *2	4,000 *2	4,000 *2	4,000 *2	4,000 *2
Reflective Integrated lens	Top-view	4 °	E32-D16 2M	40 to 2,800	40 to 2,000	40 to 1,400	40 to 900	40 to 480

*1. The fiber length is 10 m on each side, so the sensing distance is given as 20,000 mm.
*2. The fiber length is 2 m on each side, so the sensing distance is given as 4,000 mm.

Sensing method	Sensing direction	Aperture angle	Model	Sensing distance (mm)
Sensing method	Sensing direction	Aperture angle	Model	Tough mode	High- resolution mode	Standard mode	High- speed mode	Super- high- speed mode
Through-beam	Side-view	1.5 °	E32-A03 2M	3,220	2,300	1,780	1,200	500
		1.5 °	E32-A03-1 2M	3,220	2,300	1,780	1,200	500
		3.4 °	E32-A04 2M	1,280	920	680	450	200
		4 °	E32-T24SR 2M	4,000 *	2,960	2,200	1,460	580
			E32-T24S 2M	4,000 *	3,500	2,600	1,740	700
			E32-T22S 2M	4,000 *	4,000 *	3,800	2,500	1,000

* The fiber length is 2 m on each side, so the sensing distance is given as 4,000 mm.

Sensing method	Sensing direction	Model	Sensing distance (mm)
Sensing method	Sensing direction	Model	Tough mode	High- resolution mode	Standard mode	High-speed mode	Super-high- speed mode
Limited-reflective	Flat-view	E32-L16-N 2M	0 to 15				0 to 12
	Flat-view	E32-L24S 2M	0 to 4
	Side-view	E32-L25L 2M	5.4 to 9 (center 7.2)

Sensing method	Feature	Size	Model	Sensing distance (mm)
Sensing method	Feature	Size	Model	Tough mode	High- resolution mode	Standard mode	High- speed mode	Super- high- speed mode
Retro- reflective	Film detection	M3	E32-C31 2M + E39-F3R + E39-RP37	250			200	-
	Square	-	E32-R16 2M	150 to 1,500
	Threaded Models	M6	E32-R21 2M	10 to 250
	Hex-shaped	M6	E32-LR11NP 2M + E39-RP1	1,350	1,270	1,200	1,000	550

Sensing method	Feature	Sensing direction	Model	Sensing distance (mm)
Sensing method	Feature	Sensing direction	Model	Tough mode	High- resolution mode	Standard mode	High- speed mode	Super- high- speed mode
Limited- reflective	Small size	Flat-view	E32- L24S 2M	0 to 4
	Standard		E32-L16-N 2M	0 to 15				0 to 12
	Glass substrate alignment, 70 °C		E32-A08 2M	10 to 20				-
	Standard/ long-distance		E32-A12 2M	12 to 30				-
	Side view form	Side-view	E32-L25L 2M	5.4 to 9 (center 7.2)
	Glass substrate mapping, 70 °C	Top-view	E32-A09 2M	15 to 38				-

Sensing method	Type	Sensing direction	Model	Sensing distance (mm)
Sensing method	Type	Sensing direction	Model	Tough mode	High- resolution mode	Standard mode	High- speed mode	Super- high- speed mode
Through- beam	Oil-resistant	Right-angle	E32-T11NF 2M	4,000 *1	4,000 *1	4,000 *1	4,000 *1	2,200
	Chemical/ oil-resistant	Top-view	E32-T12F 2M	4,000 *1	4,000 *1	4,000 *1	4,000 *1	1,600
		Top-view	E32-T11F 2M	4,000 *1	4,000 *1	4,000 *1	2,600	1,000
		Side-view	E32-T14F 2M	1,400	1,000	800	500	200
	Chemical/oil- resistant at 150 °C	Top-view	E32-T51F 2M	4,000 *1	3,600	2,800	1,800	700
Reflective	Semiconductors: Cleaning, developing, and etching; 60°C	Top-view	E32-L11FP 2M	8 to 20 mm from tip of lens (Recommended detection distance: 11 mm), 19 to 31 mm from center of mounting hole A (Recommended detection distance: 22 mm)
	Semiconductors: Resist stripping; 85°C		E32-L11FS 2M	8 to 20 mm from tip of lens (Recommended detection distance: 11 mm), 32 to 44 mm from center of mounting hole A (Recommended detection distance: 35 mm)
	Chemical/ oil-resistant		E32-D12F 2M	- *2	320	190	130	60
	Chemical-resistant cable		E32-D11U 2M	840	600	350	240	100

*1. The fiber length is 2 m on each side, so the sensing distance is given as 4,000 mm.
*2. Even if there is no sensing object, the sensor will detect light that is reflected by the fluororesin.

Sensing method	Size	Model	Sensing distance (mm)
Sensing method	Size	Model	Tough mode	High- resolution mode	Standard mode	High- speed mode	Super-high- speed mode
Through-beam	1.5 dia.	E32-T22B 2M	680	480	400	220	90
	M3	E32-T21 2M	680	480	400	220	90
	M4	E32-T11 2M	2,500	1,800	1,350	900	360
	Square	E32-T25XB 2M	500	360	300	170	70
Reflective	1.5 dia.	E32-D22B 2M	140	100	60	40	16
	M3	E32-D21 2M	140	100	60	40	16
	3 dia.	E32-D221B 2M	300	220	140	90	40
	M4	E32-D21B 2M	300	220	140	90	40
	M6	E32-D11 2M	840	600	350	240	100
	Square	E32-D25XB 2M	240	170	100	60	30

Sensing method	Heat-resistant temperature	Model	Sensing distance (mm)
Sensing method	Heat-resistant temperature	Model	Tough mode	High- resolution mode	Standard mode	High- speed mode	Super- high- speed mode
Through-beam	100 °C	E32-T51R 2M	1,600	1,100	800	560	225
	150 °C	E32-T51 2M	2,800	2,000	1,500	1,000	400
	200 °C	E32-T81R-S 2M	1,000	720	550	360	140
	350 °C	E32-T61-S 2M	1,680	1,200	900	600	240
Reflective	100 °C	E32-D51R 2M	670	480	280	190	80
	150 °C	E32-D51 2M	1,120	800	450	320	144
	200 °C	E32-D81R-S 2M	420	300	180	120	54
	300 °C	E32-A08H2 2M	10 to 20				-
	300 °C	E32-A09H2 2M	20 to 30 (center 25)				-
	350 °C	E32-D611-S 2M	420	300	180	120	54
	350 °C	E32-D61-S 2M	420	300	180	120	54
	400 °C	E32-D73-S 2M	280	200	120	80	36

Sensing method	Type	Sensing width	Model	Sensing distance (mm)
Sensing method	Type	Sensing width	Model	Tough mode	High- resolution mode	Standard mode	High- speed mode	Super- high- speed mode
Through-beam	Area	11 mm	E32-T16PR 2M	3,100	2,200	1,700	1,120	440
		11 mm	E32-T16JR 2M	2,750	2,000	1,500	960	380
		30 mm	E32-T16WR 2M	4,000 *	3,400	2,600	1,700	680
Reflective	Array	11 mm	E32-D36P1 2M	700	500	300	200	90

* The fiber length is 2 m on each side, so the sensing distance is given as 4,000 mm.

Sensing method	Tube diameter	Feature	Model	Sensing distance (mm)
Sensing method	Tube diameter	Feature	Model	Tough mode	High- resolution mode	Standard mode	High- speed mode	Super- high- speed mode
Tube-mounting	3.2/6.4/ 9.5 dia	Stable residual quantity detection	E32-A01 5M	Applicable tube: Transparent tube with a diameter of 3.2, 6.4, or 9.5 mm, Recommended wall thickness: 1 mm
	8 to 10 dia	Mounting at multi levels	E32-L25T 2M	Applicable tube: Transparent tube with a diameter of 8 to 10 mm, Recommended wall thickness: 1 mm
	No restrictions	Large tubes	E32-D36T 2M	Applicable tube: Transparent tube (no restrictions on diameter)
Liquid contact (heat-resistant up to 200 °C)	-	-	E32-D82F1 4M	Liquid-contact Type

Sensing method	Heat- resistant temperature	Model	Sensing distance (mm)
Sensing method	Heat- resistant temperature	Model	Tough mode	High- resolution mode	Standard mode	High- speed mode	Super-high- speed mode
Through-beam	120 °C	E32-T51V 1M	720	520	400	260	100
	120 °C	E32-T51V 1M + E39-F1V	2,000 *	2,000 *	2,000 *	1,360	520
	200 °C	E32-T84SV 1M	1,760	1,250	950	640	260

* The fiber length is 1 m on each side, so the sensing distance is given as 2,000 mm.

Sensing method	Application	Operating temperature	Model	Sensing distance (mm)
Sensing method	Application	Operating temperature	Model	Tough mode	High- resolution mode	Standard mode	High- speed mode	Super- high- speed mode
Limited- reflective	Glass presence detection	70 °C	E32-L16-N 2M	0 to 15				0 to 12
	Glass substrate alignment	70 °C	E32-A08 2M	10 to 20				-
		300 °C	E32-A08H2 2M	10 to 20				-
		70 °C	E32-A12 2M	12 to 30				-
	Glass substrate mapping	70 °C	E32-A09 2M	15 to 38				-
	Glass substrate mapping	300 °C	E32-A09H2 2M	20 to 30				-
	Wet processes: Cleaning, Resist developing and etching	60 °C	E32-L11FP 2M	8 to 20 mm from tip of lens (Recommended detection distance: 11 mm), 19 to 31 mm from center of mounting hole A (Recommended detection distance: 22 mm)
	Wet process: Resist stripping	85 °C	E32-L11FS 2M	8 to 20 mm from tip of lens (Recommended detection distance: 11 mm), 32 to 44 mm from center of mounting hole A (Recommended detection distance: 35 mm)
Through- beam	Wafer mapping	70 °C	E32-A03 2M	3,220	2,300	1,780	1,200	500
			E32-A03-1 2M	3,220	2,300	1,780	1,200	500
			E32-A04 2M	1,280	920	680	450	200
			E32-T24SR 2M	4,000 *	2,960	2,200	1,460	580
			E32-T24S 2M	4,000 *	3,500	2,600	1,740	700

* The fiber length is 2 m on each side, so the sensing distance is given as 4,000 mm.

Sensing method	Sensing direction	Size	Model	Sensing distance (mm)
Sensing method	Sensing direction	Size	Model	Tough mode	High- resolution mode	Standard mode	High- speed mode	Super- high- speed mode
Through-beam	Right-angle	M4	E32-T11N 2M	1,000	700	500	350	140
	Right-angle		E32-LT11N 2M	3,200	2,300	1,750	1,150	460
	Straight		E32-T11R 2M	1,000	700	530	350	140
			E32-LT11 2M	3,800	2,700	2,050	1,350	540
			E32-LT11R 2M	3,200	2,300	1,750	1,150	460
Reflective	Right-angle	M3	E32-C31N 2M	55	40	25	23	7
		M3	E32-C21N 2M	145	75	65	45	20
		M4	E32-D21N 2M	420	300	175	120	50
		M6	E32-C11N 2M	390	280	175	160	50
		M6	E32-LD11N 2M	420	300	170	120	50
	Straight	M3	E32-D21R 2M	70	50	30	20	8
			E32-C31 2M	165	120	75	50	22
			E32-C31M 1M	165	120	75	50	22
		M4	E32-D211R 2M	70	50	30	20	8
		M6	E32-D11R 2M	420	300	170	120	50
			E32-CC200 2M	700	500	300	200	90
			E32-LD11 2M	430	305	180	125	55
			E32-LD11R 2M	420	300	170	120	50

Sensing method	Size	Sensing direction	Model	Sensing distance (mm)
Sensing method	Size	Sensing direction	Model	Tough mode	High- resolution mode	Standard mode	High- speed mode	Super- high- speed mode
Through- beam	1 dia.	Top-view	E32-T223R 2M	220	160	130	75	30
	1.5 dia.		E32-T22B 2M	340	240	200	110	45
	3 dia.		E32-T12R 2M	1,000	700	530	350	140
	3 dia.	Side-view	E32-T14LR 2M	370	270	210	130	50
Reflective	1.5 dia.	Top-view	E32-D22B 2M	70	50	30	20	8
	1.5 dia. + 0.5 dia.		E32-D43M 1M	15	11	6	4	2
	3 dia.		E32-D22R 2M	70	50	30	20	8
			E32-D221B 2M	150	110	70	45	20
			E32-D32L 2M	350	250	150	100	45
	3 dia. + 0.8 dia.		E32-D33 2M	35	25	16	10	4

Sensing method	Sensing direction	Model	Sensing distance (mm)
Sensing method	Sensing direction	Model	Tough mode	High- resolution mode	Standard mode	High- speed mode	Super- high- speed mode
Through-beam	Top-view	E32-T15XR 2M	1,000	700	530	350	140
	Side-view	E32-T15YR 2M	370	270	210	130	50
	Flat-view	E32-T15ZR 2M	370	270	210	130	50
Reflective	Top-view	E32-D15XR 2M	420	300	170	120	50
	Side-view	E32-D15YR 2M	100	70	40	26	12
	Flat-view	E32-D15ZR 2M	100	70	40	26	12

Sensing method	Sensing direction	Model	Sensing distance (mm)
Sensing method	Sensing direction	Model	Tough mode	High- resolution mode	Standard mode	High- speed mode	Super-high- speed mode
Through-beam	Side-view	E32-T24R 2M	85	60	50	25	10
	Side-view	E32-T24E 2M	225	150	125	75	30
	Top-view	E32-T21-S1 2M	255	180	150	85	34
		E32-T33 1M	75	55	45	25	10
		E32-TC200BR 2M	1,000	700	530	350	140
Reflective	Side-view	E32-D24R 2M	35	26	15	10	4
	Side-view	E32-D24-S2 2M	60	40	26	23	7
	Top-view	E32-D43M 1M	15	11	6	4	2
		E32-D331 2M	7	5	3	2	0.8
		E32-D33 2M	35	25	16	10	4
		E32-D32-S1 0.5M	31	21	13	9	3
		E32-D31-S1 0.5M	31	21	13	9	3
		E32-DC200F4R 2M	70	50	30	20	8
		E32-D22-S1 2M	125	85	55	36	15
		E32-D21-S3 2M	125	85	55	36	15
		E32-DC200BR 2M	420	300	170	120	50
		E32-D25-S3 2M	125	85	55	36	15

Type	Spot diameter	Center distance (mm)	Model	Sensing distance (mm)
Type	Spot diameter	Center distance (mm)	Model	Tough mode	High- resolution mode	Standard mode	High- speed mode	Super- high- speed mode
Variable spot	0.1 to 0.6 dia.	6 to 15	E32-C42 1M + E39-F3A	Spot diameter of 0.1 to 0.6 mm at 6 to 15 mm.
Variable spot	0.3 to 1.6 dia.	10 to 30	E32-C42 1M + E39-F17	Spot diameter of 0.3 to 1.6 mm at 10 to 30 mm.
Parallel light	4 dia.	0 to 20	E32-C31 2M + E39-F3C	Spot diameter of 4 mm max. at 0 to 20 mm.
Parallel light	4 dia.	0 to 20	E32-C31N 2M + E39-F3C	Spot diameter of 4 mm max. at 0 to 20 mm.
Integrated lens	0.1 dia.	5	E32-C42S 1M	Spot diameter of 0.1 mm at 5 mm.
Integrated lens	6 dia.	50	E32-L15 2M	Spot diameter of 6 mm at 50 mm.
Small-spot	0.1 dia.	7	E32-C41 1M + E39-F3A-5	Spot diameter of 0.1 mm at 7 mm.
	0.5 dia.		E32-C31 2M + E39-F3A-5	Spot diameter of 0.5 mm at 7 mm.
	0.5 dia.		E32-C31N 2M + E39-F3A-5	Spot diameter of 0.5 mm at 7 mm.
	0.2 dia.	17	E32-C41 1M + E39-F3B	Spot diameter of 0.2 mm at 17 mm.
	0.5 dia.		E32-C31 2M + E39-F3B	Spot diameter of 0.5 mm at 17 mm.
	0.5 dia.		E32-C31N 2M + E39-F3B	Spot diameter of 0.5 mm at 17 mm.
	3 dia.	50	E32-CC200 2M + E39-F18	Spot diameter of 3 mm at 50 mm.
	3 dia.	50	E32-C11N 2M + E39-F18	Spot diameter of 3 mm at 50 mm.

Type	Sensing direction	Aper- ture angle	Model	Sensing distance (mm)
Type	Sensing direction	Aper- ture angle	Model	Tough mode	High- resolution mode	Standard mode	High- speed mode	Super- high- speed mode
Through- beam Integrated lens	Right-angle	15 °	E32-LT11N 2M	3,200	2,300	1,750	1,150	460
	Top-view	10 °	E32-T17L 10M	20,000 *1	20,000 *1	20,000 *1	10,000	4,000
		15 °	E32-LT11 2M	3,800	2,700	2,050	1,350	540
		15 °	E32-LT11R 2M	3,200	2,300	1,750	1,150	460
	Side-view	30 °	E32-T14 2M	4,000 *2	4,000 *2	3,400	2,250	900
Through- beam models with lenses	Right-angle	12 °	E32-T11N 2M + E39-F1	4,000 *2	4,000 *2	3,700	2,400	970
	Right-angle	6 °	E32-T11N 2M + E39-F16	4,000 *2	4,000 *2	4,000 *2	4,000 *2	1,800
	Top-view	12 °	E32-T11R 2M + E39-F1	4,000 *2	4,000 *2	3,700	2,400	970
	Top-view	6 °	E32-T11R 2M + E39-F16	4,000 *2	4,000 *2	4,000 *2	4,000 *2	1,800
	Side-view	60 °	E32-T11R 2M + E39-F2	725	520	400	250	100
	Top-view	12 °	E32-T11 2M + E39-F1	4,000 *2	4,000 *2	3,600	2,300	930
	Top-view	6 °	E32-T11 2M + E39-F16	4,000 *2	4,000 *2	4,000 *2	4,000 *2	2,300
	Side-view	60 °	E32-T11 2M + E39-F2	1,150	820	660	430	160
	Top-view	12 °	E32-T51R 2M + E39-F1	4,000 *2	3,900	2,900	1,900	760
	Top-view	6 °	E32-T51R 2M + E39-F16	4,000 *2	4,000 *2	4,000 *2	3,600	1,400
	Side-view	60 °	E32-T51R 2M + E39-F2	700	500	360	250	100
	Top-view	12 °	E32-T81R-S 2M + E39-F1	4,000 *2	2,650	2,100	1,300	520
	Top-view	6 °	E32-T81R-S 2M + E39-F16	4,000 *2	4,000 *2	3,600	2,300	900
	Side-view	60 °	E32-T81R-S 2M + E39-F2	500	360	280	180	70
	Top-view	12 °	E32-T61-S 2M + E39-F1	4,000 *2	4,000 *2	3,400	2,200	900
	Top-view	6 °	E32-T61-S 2M + E39-F16	4,000 *2	4,000 *2	4,000 *2	3,900	1,500
	Side-view	60 °	E32-T61-S 2M + E39-F2	840	600	450	300	120
	Top-view	12 °	E32-T51 2M + E39-F1-33	4,000 *2	3,400	2,660	1,150	700
	Top-view	6 °	E32-T51 2M + E39-F16	4,000 *2	4,000 *2	4,000 *2	4,000 *2	2,600
Reflective Integrated lens	Top-view	4 °	E32-D16 2M	40 to 1,400	40 to 1,000	40 to 700	40 to 450	40 to 240

*1. The fiber length is 10 m on each side, so the sensing distance is given as 20,000 mm.
*2. The fiber length is 2 m on each side, so the sensing distance is given as 4,000 mm.

Sensing method	Sensing direction	Aperture angle	Model	Sensing distance (mm)
Sensing method	Sensing direction	Aperture angle	Model	Tough mode	High- resolution mode	Standard mode	High- speed mode	Super- high- speed mode
Through- beam	Side-view	1.5 °	E32-A03 2M	1,610	1,150	890	600	250
		1.5 °	E32-A03-1 2M	1,610	1,150	890	600	250
		3.4 °	E32-A04 2M	640	460	340	225	100
		4 °	E32-T24SR 2M	2,100	1,500	1,100	750	300
			E32-T24S 2M	2,400	1,750	1,300	870	350
			E32-T22S 2M	3,500	2,500	1,900	1,250	500

Sensing method	Sensing direction	Model	Sensing distance (mm)
Sensing method	Sensing direction	Model	Tough mode	High- resolution mode	Standard mode	High- speed mode	Super-high- speed mode
Limited-reflective	Flat-view	E32-L16-N 2M	0 to 15				0 to 12
	Flat-view	E32-L24S 2M	0 to 4
	Side-view	E32-L25L 2M	5.4 to 9 (center 7.2)

Sensing method	Feature	Size	Model	Sensing distance (mm)
Sensing method	Feature	Size	Model	Tough mode	High- resolution mode	Standard mode	High- speed mode	Super- high- speed mode
Retro- reflective	Film detection	M3	E32-C31 2M + E39-F3R + E39-RP37	250	200	150	100	50
	Square	-	E32-R16 2M	150 to 1,500
	Threaded Models	M6	E32-R21 2M	10 to 250
	Hex-shaped	M6	E32-LR11NP 2M + E39-RP1	675	630	600	500	275

Sensing method	Feature	Sensing direction	Model	Sensing distance (mm)
Sensing method	Feature	Sensing direction	Model	Tough mode	High- resolution mode	Standard mode	High- speed mode	Super- high- speed mode
Limited- reflective	Small size	Flat-view	E32- L24S 2M	0 to 4
	Standard		E32-L16-N 2M	0 to 15				0 to 12
	Glass substrate alignment, 70 °C		E32-A08 2M	10 to 20
	Standard/ long-distance		E32-A12 2M	12 to 30
	Side view form	Side-view	E32-L25L 2M	5.4 to 9 (center 7.2)
	Glass substrate mapping, 70 °C	Top-view	E32-A09 2M	15 to 38

Sensing method	Type	Sensing direction	Model	Sensing distance (mm)
Sensing method	Type	Sensing direction	Model	Tough mode	High- resolution mode	Standard mode	High- speed mode	Super- high- speed mode
Through- beam	Oil-resistant	Right-angle	E32-T11NF 2M	4,000 *1	4,000 *1	4,000 *1	3,100	1,200
	Chemical/oil-resistant	Top-view	E32-T12F 2M	4,000 *1	4,000 *1	3,000	2,000	800
		Top-view	E32-T11F 2M	3,500	2,500	2,000	1,300	520
		Side-view	E32-T14F 2M	700	500	400	250	100
	Chemical/ oil-resistant at 150 °C	Top-view	E32-T51F 2M	2,500	1,800	1,400	900	350
Reflective	Semiconductors: Cleaning, developing, and etching; 60°C	Top-view	E32-L11FP 2M	8 to 20 mm from tip of lens (Recommended detection distance: 11 mm), 19 to 31 mm from center of mounting hole A (Recommended detection distance: 22 mm)
	Semiconductors: Resist stripping; 85°C		E32-L11FS 2M	8 to 20 mm from tip of lens (Recommended detection distance: 11 mm), 32 to 44 mm from center of mounting hole A (Recommended detection distance: 35 mm)
	Chemical/oil-resistant		E32-D12F 2M	- *2	160	95	65	30
	Chemical-resistant cable		E32-D11U 2M	420	300	170	120	50

*1. The fiber length is 2 m on each side, so the sensing distance is given as 4,000 mm.
*2. Even if there is no sensing object, the sensor will detect light that is reflected by the fluororesin.

Sensing method	Size	Model	Sensing distance (mm)
Sensing method	Size	Model	Tough mode	High-resolution mode	Standard mode	High-speed mode	Super-high- speed mode
Through-beam	1.5 dia.	E32-T22B 2M	340	240	200	110	45
	M3	E32-T21 2M	340	240	200	110	45
	M4	E32-T11 2M	1,250	900	680	450	180
	Square	E32-T25XB 2M	250	180	150	85	35
Reflective	1.5 dia.	E32-D22B 2M	70	50	30	20	8
	M3	E32-D21 2M	70	50	30	20	8
	3 dia.	E32-D221B 2M	150	110	70	45	20
	M4	E32-D21B 2M	150	110	70	45	20
	M6	E32-D11 2M	420	300	170	120	50
	Square	E32-D25XB 2M	120	85	50	30	15

Sensing method	Heat-resistant temperature	Model	Sensing distance (mm)
Sensing method	Heat-resistant temperature	Model	Tough mode	High- resolution mode	Standard mode	High- speed mode	Super- high- speed mode
Through-beam	100 °C	E32-T51R 2M	800	560	425	280	110
	150 °C	E32-T51 2M	1,400	1,000	760	500	200
	200 °C	E32-T81R-S 2M	500	360	280	180	70
	350 °C	E32-T61-S 2M	840	600	450	300	120
Reflective	100 °C	E32-D51R 2M	330	240	135	95	40
	150 °C	E32-D51 2M	560	400	230	160	72
	200 °C	E32-D81R-S 2M	210	150	90	60	27
	300 °C	E32-A08H2 2M	10 to 20
	300 °C	E32-A09H2 2M	20 to 30 (center 25)
	350 °C	E32-D611-S 2M	210	150	90	60	27
	350 °C	E32-D61-S 2M	210	150	90	60	27
	400 °C	E32-D73-S 2M	140	100	60	40	18

Sensing method	Type	Sensing width	Model	Sensing distance (mm)
Sensing method	Type	Sensing width	Model	Tough mode	High- resolution mode	Standard mode	High- speed mode	Super- high- speed mode
Through-beam	Area	11 mm	E32-T16PR 2M	1,550	1,100	840	560	220
		11 mm	E32-T16JR 2M	1,370	980	750	480	190
		30 mm	E32-T16WR 2M	2,000	1,700	1,300	850	340
Reflective	Array	11 mm	E32-D36P1 2M	350	250	150	100	45

Sensing method	Tube diameter	Feature	Model	Sensing distance (mm)
Sensing method	Tube diameter	Feature	Model	Tough mode	High- resolution mode	Standard mode	High- speed mode	Super- high- speed mode
Tube-mounting	3.2/6.4/ 9.5 dia	Stable residual quantity detection	E32-A01 5M	Applicable tube: Transparent tube with a diameter of 3.2, 6.4, or 9.5 mm, Recommended wall thickness: 1 mm
	8 to 10 dia	Mounting at multi levels	E32-L25T 2M	Applicable tube: Transparent tube with a diameter of 8 to 10 mm, Recommended wall thickness: 1 mm
	No restrictions	Large tubes	E32-D36T 2M	Applicable tube: Transparent tube (no restrictions on diameter)
Liquid contact (heat-resistant up to 200 °C)	-	-	E32-D82F1 4M	Liquid-contact Type

Sensing method	Heat-resistant temperature	Model	Sensing distance (mm)
Sensing method	Heat-resistant temperature	Model	Tough mode	High- resolution mode	Standard mode	High- speed mode	Super-high- speed mode
Through- beam	120 °C	E32-T51V 1M	360	260	200	130	50
	120 °C	E32-T51V 1M + E39-F1V	1,890	1,350	1,000	680	260
	200 °C	E32-T84SV 1M	880	630	480	320	130

Sensing method	Application	Operating temperature	Model	Sensing distance (mm)
Sensing method	Application	Operating temperature	Model	Tough mode	High- resolution mode	Standard mode	High- speed mode	Super- high- speed mode
Limited- reflective	Glass presence detection	70 °C	E32-L16-N 2M	0 to 15				0 to 12
	Glass substrate alignment	70 °C	E32-A08 2M	10 to 20
		300 °C	E32-A08H2 2M	10 to 20
		70 °C	E32-A12 2M	12 to 30
	Glass substrate mapping	70 °C	E32-A09 2M	15 to 38
	Glass substrate mapping	300 °C	E32-A09H2 2M	20 to 30 (center 25)
	Wet processes: Cleaning, Resist developing and etching	60 °C	E32-L11FP 2M	8 to 20 mm from tip of lens (Recommended detection distance: 11 mm), 19 to 31 mm from center of mounting hole A (Recommended detection distance: 22 mm)
	Wet process: Resist stripping	85 °C	E32-L11FS 2M	8 to 20 mm from tip of lens (Recommended detection distance: 11 mm), 32 to 44 mm from center of mounting hole A (Recommended detection distance: 35 mm)
Through- beam	Wafer mapping	70 °C	E32-A03 2M	1,610	1,150	890	600	250
			E32-A03-1 2M	1,610	1,150	890	600	250
			E32-A04 2M	640	460	340	225	100
			E32-T24SR 2M	2,100	1,500	1,100	750	300
			E32-T24S 2M	2,400	1,750	1,300	870	350

E3X-DA-S

Stable Detection with Advanced Fiber Amplifier Units

Fiber Amplifier Units

Wire-saving connectors

Sensing Distance

E3X-DA[]-S ([]: 21/51/7/9/0) ・ E3X-DA[]F-S([]: 21/51/7/9)

Threaded Models

Cylindrical Models

Flat Models

Sleeve Models

Small-spot, Reflective

High-power Beam

Narrow View

Detection without Background Interference

Transparent Object Detection (Retro-reflective)

Transparent Object Detection (Limited-reflective)

Chemical-resistant, Oil-resistant

Bending-resistant

Heat-resistant

Area Beam

Liquid-level Detection

Vacuum-resistant

FPD, Semiconductors, and Solar Cells

E3X-DA[]R-S ([]:21/51/7/9)

Threaded Models

Cylindrical Models

Flat Models

Sleeve Models

Small-spot, Reflective

High-power Beam

Narrow View

Detection without Background Interference

Transparent Object Detection (Retro-reflective)

Transparent Object Detection (Limited-reflective)

Chemical-resistant, Oil-resistant

Bending-resistant

Heat-resistant

Area Beam

Liquid-level Detection

Vacuum-resistant

FPD, Semiconductors, and Solar Cells

Product Category