Page top

Building Automation


Industrial Automation


Power Automation & Safety

Bangladesh Distributor

G9SX-SM

Standstill Monitoring Unit

G9SX-SM

Sensor-less Monitoring of Standstill for Machines with Long Inertia

Ratings

Power input

Model G9SX-SM032-[]
Rated supply voltage 24 VDC
Operating voltage range -15% to 10% of rated supply voltage
Power consumption * 4 W max.

* Power consumption of loads not included.

Inputs

Model G9SX-SM032-[]
Rated Input voltage Standstill detection input (between Z1 and Z2 and between Z3 and Z4) *1
480 VAC max. (120Hz max.) *2
Internal impedance Standstill detection input: Approx. 660 kΩ
EDM input: Approx. 2.8 kΩ *3

*1. Input the motor phase-to-phase voltage between Z1 and Z2 and between Z3 and Z4.
*2. When a motor with AC240V or more is used, connect neutral point of the power supply to earth.
*3. Use a contact that is applicable to microloads (24 VDC, 5 mA) for connection to the EDM input.

Outputs

Model G9SX-SM032-[]
Safety standstill detection output * 1 Source output (PNP), load current: 0.3 A DC max. * 2
Auxiliary output (output monitor/error) Source output (PNP), load current: 100 mA DC max.

*1. While safety standstill detection outputs are in the ON state, the following pulse signal is output continuously for output
       circuit diagnosis.
       When using the safety standstill detection outputs as input signals to control devices (i.e. Programmable Controllers),
       consider the pulse signal shown below.

G9SX-SM Specifications 7

*2. The following derating is required when Units are mounted side-by-side.
       G9SX-SM032-[]: 0.2 A max. load current

Characteristics

Model G9SX-SM032-[]
Over-voltage category (IEC/EN 60664-1) III
Response time
(Standstill detection ON to OFF)
50 ms max.
Detection voltage
(Standstill detection voltage)
Standard Configuration: 10 mV max.
User Configuration: 100 mV max.
ON-state residual voltage 3.0 V max. (Safety standstill detection outputs and auxiliary outputs)
OFF-state leakage current 0.1 mA max. (Safety standstill detection outputs and Auxiliary outputs)
Maximum cable length for standstill
detection inputs and EDM inputs
100 m max. (External connection impedance: 100 Ω max. and 10 nF max.)
Insulation
resistance
Between standstill
detection inputs
(Z1,Z2⇔Z3,Z4)
100 MΩ min., 500 VDC megger
Between standstill
detection input
terminals connected
together and other
input and output
terminals connected
together
Between all terminals
without standstill
detection input
terminals connected
together and DIN rail
Between standstill
detection input
terminals connected
together and DIN rail.
Dielectric
strength
Between standstill
detection inputs
(Z1,Z2⇔Z3,Z4)
2,000 VAC for 1 min.
Between standstill
detection input
terminals connected
together and Power
supply input terminals
and other input and
output terminals
connected together
2,200 VAC for 1 min.
Between all terminals
without standstill
detection input
terminals connected
together and DIN rail
500 VAC for 1 min.
Between standstill
detection input
terminals connected
together and DIN rail.
2,200 VAC for 1 min.
Vibration resistance Frequency: 10 to 55 to 10 Hz, 0.375-mm single amplitude
(0.75-mm double amplitude)
Mechanical
shock
resistance
Destruction 300 m/s2
Malfunction 100 m/s2
Ambient temperature -10 to +55 °C (no icing or condensation)
Ambient humidity 25% to 85%
Degree of protection Terminal block : IP20, Main body : IP40
Terminal tightening torque * 0.6Nm
Weight Approx. 200 g

* For G9SX-SM032-RT (with screw terminals)