ZX-T

Model	ZX-TDA11	ZX-TDA41
Measurement period	1 ms
Possible average count settings *1	1, 16, 32, 64, 128, 256, 512, or 1,024
Linear output *2	Current output: 4 to 20 mA/F.S., Max. load resistance: 300 Ω Voltage output: ±4 V (±5 V, 1 to 5 V *3), Output impedance: 100 Ω
Judgement outputs (3 outputs: HIGH/PASS/LOW)	NPN open-collector outputs, 30 VDC, 30 mA max. Residual voltage: 1.2 V max.	PNP open-collector outputs, 30 VDC, 30 mA max. Residual voltage: 2 V max.
Zero reset input, timing input, reset input, judgement output hold input	ON: Short-circuited with 0-V terminal or 1.5 V or less OFF: Open (leakage current: 0.1 mA max.)	ON: Supply voltage short-circuited or supply voltage of 1.5 V or less OFF: Open (leakage current: 0.1 mA max.)
Function	Measurement value display, Present value/set value/output value display, Display reverse, ECO mode, Number of display digit changes, Sample hold, Peak hold, Bottom hold, peak-to-peak hold, Self-peak hold, Self-bottom hold, Zero reset, Initial reset, Direct threshold value setting, Position teaching, Hysteresis width setting, Timing inputs, Reset input, Judgement output hold input, (A-B) calculations *4, (A+B) calculations *4, Sensor disconnection detection, Zero reset memory, Function lock, Non-measurement setting, Clamp value setting, Scale inversion, Zero reset indicator, Span adjustment, Warming-up display, Pressing force alarm
Indicators	Judgement indicators: High (orange), pass (green), low (yellow), 7-segment main digital display (red), 7-segment sub-digital display (yellow), power ON (green), zero reset (green), enable (green)
Power supply voltage	12 to 24 VDC ±10%, Ripple (p-p): 10% max.
Current consumption	140 mA max. (with Sensor connected), For 24-VDC power supply voltage: 140 mA max. (with Sensor connected)
Ambient temperature	Operating and storage: 0 to 50°C (with no icing or condensation)
Temperature characteristic	0.03% F.S./°C
Connection method	Prewired (standard cable length: 2 m)
Weight (packed state)	Approx. 350 g
Materials	Case: PBT (polybutylene terephthalate), Cover: Polycarbonate

*1. The response speed of the linear output is calculated as the measurement period × (average count setting + 1).
       The response speed of the judgement outputs is calculated as the measurement period × (average count setting
       + 1).
*2. The output can be switched between a current output and voltage output using a switch on the bottom of the Amplifier
       Unit.
*3. Setting is possible via the monitor focus function.
*4. A Calculating Unit (ZX-CAL2) is required.

Model		ZX-TDS01T	ZX-TDS04T	ZX-TDS04T-L
Measurement range		1 mm	4 mm
Maximum actuator travel distance		Approx. 1.5 mm	Approx. 5 mm
Resolution *1		0.1 μm
Linearity *2		0.3% F.S.
Operating force *3		Approx. 0.7 N		Approx. 0.25 N
Degree of protection (Sensor Head)		IEC60529, IP67		IEC60529, IP54
Mechanical durability		10,000,000 operations min.
Ambient temperature		Operating: 0°C to 50°C (with no icing or condensation) Storage: -15°C to 60°C (with no icing or condensation)
Ambient humidity		Operating and storage: 35% to 85% (with no icing or condensation)
Temperature characteristic *4	Sensor Head	0.03% F.S./°C
	Preamplifier	0.01% F.S./°C
Weight (packed state)		Approx. 100 g
Materials	Sensor Head	Stainless steel
	Preamplifier	Polycarbonate
Accessories		Instruction manual, Preamplifier Mounting Brackets (ZX-XBT1)

*1. The resolution is given as the minimum value that can be read when a ZX-TDA[]1 Amplifier Unit is connected. This
       value is taken 15 minutes after turning ON the power with the average number of operations set to 256.
*2. The linearity is given as the error in an ideal straight line displacement output.
*3. These figures are representative values that apply for the measurement mid-point, and are for when the provided
       actuator is used, with the actuator moving downwards. If the actuator moves horizontally or upwards, the operating
       force will be reduced. Also, if an actuator other than the standard one is used, the operating force will vary with the
       weight of the actuator itself.
*4. These figures are representative values that apply for the mid-point of the measurement range.

Model		ZX-TDS10T	ZX-TDS10T-V	ZX-TDS10T-L	ZX-TDS10T-VL
Vacuum retract (VR) and air push (AP) compatible		No	VR	No	VR/AP
Measurement range		10 mm
Maximum actuator travel distance		10.5 mm
Resolution *1 *5		0.4 μm
Linearity *2 *5		±0.5% FS
Operating force *3		Approx. 0.7 N	Approx. 0.6 N	Approx. 0.065 N	Approx. 0.09 to 1.41 N
Air pressure	Vacuum retracting	---	-0.55 to -0.70 (bar)	---	-0.22 to -0.5 (bar)
	Air push		---		0.125 to 2 (bar)
Degree of protection	Sensor Head	IP65		IP50
	Preamplifier	IP40
Mechanical durability		10,000,000 operations min.
Ambient temperature		Operating: 0 to 50°C (with no icing or condensation), Storage: -10 to 60°C (with no icing or condensation)
Ambient humidity		Operating and storage: 35% to 85% (with no icing or condensation)
Temperature characteristic *4	Sensor Head	±0.01% F.S./°C
	Preamplifier	±0.01% F.S./°C
Vibration resistance		0.35-mm single amplitude at 10 to 55 Hz for 50 min each in the X, Y, and Z directions
Shock resistance		150 m/S2 3 times each in 6 directions (up/down, left/right, and forward/backward)
Connection method		Prewired connector (2 m from the Sensor Head to the Preamplifier, 0.2 m from the Preamplifier to the connector)
Weight (packed state)		Approx. 100 g
Materials	Sensor Head	Stainless steel
	Rubber sleeve	Viton		None
	Preamplifier	Polycarbonate
	Mounting Brackets	Stainless steel		Polyamide
Accessories		Instruction manual, Preamplifier Mounting Brackets (ZX-XBT1), Right- angle Adapter *6

*1. The resolution indicates the variation (±3 σ) in the linear output (voltage output) when a ZX-TDA[]1 Amplifier Unit is
       connected. This value is taken 30 minutes after turning ON the power with the average number of operations set to
       1,024. The minimum value that can be read is 1 μm.
*2. The linearity is given as the error in an ideal straight line displacement output.
*3. These figures are representative values that apply for the mid-point of the measurement range when the Actuator
      provided is secured facing downward.
      - ZX-TDS10T and ZX-TDS10T-V: The operating force will be reduced if the Actuator is secured facing horizontally or
        upward.
      - ZX-TDS10T-L and ZX-TDS10T-VL: The actuator can be installed only facing downward.
*4. These figures are representative values that apply for the mid-point of the measurement range.
*5. These values were measured at an ambient temperature of 23°C.
*6. The ZX-TDS10T comes with a Right-angle Adapter.