S8VS-09024

Switch Mode Power Supply (15/30/60/90/120/180/240/480-W Models)

Image

Covered type, Natural air-cooling, Input: 80 to 370 VDC 100 to 240 VAC, Power ratings: 90 W, Output: 24 VDC

Power rating	90 W
Rated input voltage	100 to 240 VAC
Output voltage	24 VDC
Heat radiation	Natural air-cooling
Construction	Covered type
Terminal type	Screw terminal
Mounting type	DIN Rail mounting type

Item list of S8VS

Ratings / Performance
Outline drawing
Connection diagram
Derating curve

Ratings / Performance

As of October 10, 2016


Power rating	90 W
Efficiency	83% TYP.(At 100 VAC input) 84% TYP.(At 200 VAC input)
Rated input voltage	100 to 240 VAC
Allowable input voltage variable range	85 to 264 VAC 80 to 370 VDC
Note at DC input	The range for compliance with EC Directives and safety standards (UL, EN, etc.) is 100 to 240 VAC (85 to 264 VAC).
Frequency	50/60 Hz(47 to 450 Hz Single-phase)
Rated input curren	1.9A TYP. (At 100 VAC input) 1.0A TYP. (At 200 VAC input)
Leakage current	0.5 mA Max. (At 100 VAC input) 1.0 mA Max. (At 200 VAC input)
Inrush current	14 A TYP. (At 100 VAC input (For cold start at 25 CEL)) 28 A TYP. (At 200 VAC input (For cold start at 25 CEL))
Output voltage	24 VDC
Output voltage variable range	-10 to +15 % (With V. ADJ) (The output voltage may increase beyond the allowable voltage range (up to +15% of the rated voltage) depending on the operation of the output voltage adjuster (V.ADJ). When adjusting the output voltage, check the output voltage of the Power Supply and be sure that the load is not damaged.)
Ripple	2%(p-p) Max. (Under the rated I/O conditions.) 250mV Max. (Under the rated I/O conditions.)
Static input variation influence	0.5% Max. At 85 to 264 VAC input, 100% load
Static load variation influence	1.5% Max. At rated input, 0 to 100% load
Ambient temperature variation influence	0.05 %/CEL Max.
Rated output current	3.75 A
Start up time	460 ms TYP. (100 VAC input) 300 ms TYP. (200 VAC input)
Hold time	28ms TYP. (100 VAC input) 132ms TYP. (200 VAC input)
Overload protection	105% to 160% of the rated output current Inverted L voltage drop, Intermittent operation, Automatic reset
Overvoltage protection	Operated at 115 to 150 % of the rated output voltage, Shut-off Resetting: Reset the power by turning it back (OFF time: at least 3 min)
Overheat protection	No
Maintenance forecast monitor output	No
Total run time monitor output	No
Undervoltage alarm output	No
Power failure alarm output	No
Parallel operation	No (However, backup operation is possible; external diodes required.)
N+1 redundant system	-
Series operation	Yes (Up to 2 Power Supplies with external diode)
Remote sensing function	No
Dielectric strength	Between all inputs and all outputs/alarm outputs: 3 kVAC for 1 min (Detection current: 20 mA) Between all inputs and PE terminals: 2 kVAC for 1 min (Detection current: 20 mA) Between all outputs/alarm outputs and all PE terminals: 1 kVAC for 1 min (Detection current: 30 mA) Between all outputs and all alarm outputs: 500 VAC for 1 min (Detection current: 20 mA)
Insulation resistance	Between all outputs/alarm outputs and all inputs/PE terminals: 100 MOhm Min. (at 500 VDC)
Vibration resistance	10 to 55 Hz, 0.375 mm single amplitude in each 3 directions for 2 hours
Shock resistance	150 m/s**2, in each 6 directions 3 times
Output indicator	Yes (color: green)
Heat radiation	Natural air-cooling
Construction	Covered type
Terminal type	Screw terminal
Mounting type	DIN Rail mounting type
Weight (Main)	Approx. 490 g

Do not use the Inverter output for the Power Supply. Inverters with an output frequency of 50/60 Hz are available, but the rise in the internal temperature of the Power Supply may result in ignition or burning.

As of October 10, 2016