H5CX-A11S-N

Digital Timer

Image

Digital Timer, 48×48×84.1 mm, 100 to 240 VAC

Rated supply voltage	100 to 240 VAC 50/60 Hz
Time range	0.001s to 9999h
Input method	No-voltage/Voltage input (Switchable)
Output modes	A (Signal ON delay1) A-1 (Signal ON delay2) A-2 (Power ON delay1) A-3 (Power ON delay2) b (Repeat cycle1) b-1 (Repeat cycle2) d (Signal OFF delay) E (Interval) F (Cumulative) Z (ON/OFF-duty adjustable flicker) S (Stopwatch) toff (Flicker OFF start1) ton (Flicker ON start1) toff-1 (Flicker OFF start2) ton-1 (Flicker ON start2)
Control output	Transistor output (NPN open collector)
Display method	7-segment negative transmissive LCD
Character height	Present value: 12 mm (Red) Equipped Set value: 6 mm (Green)
External connection method	11-pin round socket

Item list of H5CX

Ratings/Performance
Dimensions
Terminal arrangement
Input connections
Operating chart

Ratings/Performance

As of August 8, 2016


Rated supply voltage	100 to 240 VAC 50/60 Hz
Operating voltage range	85% to 110% of rated supply voltage
Power consumption	Approx. 6.2VA
Time ranges（Number of ranges）	10
Time ranges	0.001 s to 9.999 s / 0.01 s to 99.99 s / 0.1 s to 999.9 s / 1 s to 9999 s / 0.1 min to 999.9 min / 1 min to 9999 min / 0.1 h to 999.9 h / 1 h to 9999 h 1sec～99min59sec
Select method	Dip switch or Operation Key
Input signals	Signal, Gate, Reset
Input method	No-voltage/Voltage input (Switchable)
No-voltage input（Solid state input）	ON impedance: 1 kOhm max. Leakage current: Approx. 12 mA ON residual voltage: 3 V max. OFF impedance: 100 kOhm min. (The DC voltage must be 30 VDC max.)
No-voltage input（Contact input）	Use contact which can adequately switch 5 mA at 10 V (The DC voltage must be 30 VDC max.)
No-voltage input（Applicable two-wire sensor）	Leakage current: 1.5 mA max. Switching capacity: 5 mA min. Residual voltage3.0 VDC max. Operating voltage: 10 VDC
Voltage input	High level: 4.5 to 30 VDC Low level: 0 to 2 VDC Input resistance: 4.7 kOhm (The DC voltage must be 30 VDC max.)
Minimum input signal width	1 ms/ 20 ms (Switchable)(Signal, Reset, Gate)
Standby time	250 ms max. (Control output is turned OFF and no input is accepted during sensor waiting time.)
Output modes	A (Signal ON delay1) A-1 (Signal ON delay2) A-2 (Power ON delay1) A-3 (Power ON delay2) b (Repeat cycle1) b-1 (Repeat cycle2) d (Signal OFF delay) E (Interval) F (Cumulative) Z (ON/OFF-duty adjustable flicker) S (Stopwatch) toff (Flicker OFF start1) ton (Flicker ON start1) toff-1 (Flicker OFF start2) ton-1 (Flicker ON start2)
Control output （Solid state output）	Transistor output (NPN open collector) Switching capacities: 100 mA max. 30 VDC max. Residual voltage: 1.5(Ability approx.1) Leakage current: 0.1
One-shot output time	0.01 to 99.99 s
Reset system	Power reset(A,A-1,A-2,b,d,E,Z,S,ton,toff mode) / Automatic reset(A-1,b,b-1,d,E,Z,ton,toff,S,ton-1,toff-1 mode) / External reset / Manual reset
Power reset	Minimum power-opening time: 0.5 s (except for A-3, b-1, F, ton-1 and toff-1 mode)
Timer mode	Elapsed time (UP) and remaining time (DOWN) (selectable)
Display method	7-segment negative transmissive LCD
Digit	4 digit
Character height	Present value: 12 mm (Red) Equipped Set value: 6 mm (Green)
Key protect method	Key protect Switch
Memory backup method	EEP-ROM Number of rewite: 100000 times min. / Service life: 10 years min.
Ambient temperature	Operating: -10 to 55 ℃ When mount timer side by side: -10 to 50 CEL Storag: -25 to 70 ℃ (with no icing or condensation)
Ambient humidity	Operating: 25 to 85%RH Storag: 25 to 85%RH
Total accuracy	Accuracy of operating time and setting error (including temperature and voltage influences) Power-ON start: +/- 0.01% +/- 50 ms max. The values are based on the set value. Accuracy of operating time and setting error (including temperature and voltage influences) Signal start: +/- 0.005% +/- 3 ms max. (The value is applied for a minimum pulse width of 1 ms.) The values are based on the set value.
Insulation resistance	100 MΩ min. (at 500 VDC) between current carrying metal parts and exposed non-current carrying metal parts / between non-continuous contacts
Dielectric strength	between current-carrying metal parts and non-curernt-carrying metal parts: 2000 between operating power circuit and input circuit: 2000 between input and control output and operation power circuit: 2000 between non-continuous contacts: 1000
Impulse withstand voltage	between power terminals: 5 kV between current-carrying terminals and exposed non-curernt-carrying metal parts: 5 kV
Noise immunity	Between power terminals: +/- 1.5 kV Between input terminals: +/- 600 V Square-wave noise by noise simulator (Pulse width: 100 ns/1 us, Rise: 1-ns)
Static immunity	Mulfunction: 8 kV ,Destruction: 15 kV
Vibration resistance （Destruction）	10 to 55 Hz, 0.75 mm single amplitude in each 3 directions for 2 hours
Vibration resistance （Malfunction）	10 to 55 Hz 0.35 mm single amplitude in each 3 directions for 10 min
Shock resistance （Destruction）	300 m/s**2, in each 6 directions (3 axes) 3 times
Shock resistance （Malfunction）	100 m/s**2, in each 6 directions (3 axes) 3 times
Degree of protection	Panel surface: IEC IP66, UL508 Type 4X (indoors) (when using the Y92S-29 Waterproof Packing and Y92F-30 Flush Mounting Adapter) / Case rear: IP40 / Terminal block: IP20
Mounting method	Flush mounting / Surface mounting
External connection method	11-pin round socket
Case color	Black (Munsell N1.5) (The front part can be changed to light gray or white in sold separately panel)
Attachment	Label for DIP switch settings
Accessory (sold separately)	Y92A-48F1: Soft Cover Y92A-48: Hard Cover Y92F-30: Flush Mounting Adapter Y92F-45: Flush Mounting Adapter Y92S-29: Waterproof Packing Y92P-CXT4S: Replacement Front Panel Y92P-CXT4G: Replacement Front Panel Y92P-CXT4B: Replacement Front Panel
Weight	約115g