Page top

Building Automation


Industrial Automation


Power Automation & Safety

Bangladesh Distributor

CJ1W-PTS

CJ-series Process Analog I/O Unit

CJ1W-PTS

A Single Unit Handling All Types of Inputs such as Temperature Sensor Inputs and Analog Signal Inputs (e.g., 4 to 20 mA or 1 to 5 V)

about this Product Family

CJ1W-PTS15 Isolated-type Thermocouple Input Unit

Item Specifications
Model CJ1W-PTS15
Applicable Controller CJ Series
Unit classification CJ-series Special I/O Unit
Mounting position CJ-series CPU Rack or CJ-series Expansion Rack
Maximum number of Units 40 (within the allowable current consumption and power consumption range)
Unit numbers 00 to 95 (Cannot duplicate Special I/O Unit numbers.)
Areas for
data
exchange
with CPU
Unit
Special I/O Unit Area
(Operation Data)
10 words/Unit
Thermocouple Input Unit to CPU Unit:
All process values, process value alarms (LL, L, H, HH), conversion data enabled flags, sensor errors.
DM Area words
allocated to Special
I/O Units
(Setting parameter)
100 words/Unit
CPU Unit to Thermocouple Input Unit:
Temperature sensor type, input range (user set), process value alarm setting (L, H), zero/span
adjustment value.
Expansion Control/
Monitor Area words
(Expansion
Operation Data)
35 words/Unit
CPU Unit to Thermocouple Input Unit:
Hold function selection start/reset, adjustment period control, control bits
Thermocouple Input Unit to CPU Unit:
Adjustment period warnings/notices (for each input), peak and bottom values, top and valley values
Expansion Setting
Area words
(Expansion Setting
parameter)
46 words/Unit
CPU Unit to Thermocouple Input Unit:
Expansion Setting Area settings, adjustment period control, peak and bottom detection, top and valley
detection
Number of temperature sensor
inputs
2
Temperature sensor type The sensor type, input range, and scaling can be set individually for each of 2 inputs, which are each
selectable from B, E, J, K, L, N, R, S, T, U, WRe5-26, PL II, and mV.
Scaling Data to be stored in the allocated words in the CIO area must be scaled (with the minimum and
maximum values set by user) (2 inputs set separately). For example, data can be stored at 0% to 100%.
Data storage in the CIO Area The value derived from carrying out the following processing in order of the actual process data in
the input range is stored in four digits hexadecimal (binary values) in the allocated words in the CIO
Area.
1) Mean value processing → 2) Scaling → 3) Zero/span adjustment → 4) Output limits
Accuracy (25 ° C) ±0.05% (Depends on the Sensor used and the measured temperature. Refer to Accuracy by Sensor
Type and Measured Temperature Range on Data Sheet for details.)
Temperature coefficient ±0.01%/°C (For full scale of electromotive force. *)
Resolution 1/64000
Cold junction compensation
error
±1°C, at 20 ±10°C
Maximum signal input ±120 mV
Input impedance 20 kΩ min.
Input disconnection detection
current
0.1 μA (typical)
Warmup time 45 min
Response time 100 ms (travel time from input 0% to 90%, for ±100 mV step input and with moving average for 4
samples)
Conversion period 10 ms/2 inputs
Maximum time to store data in
CPU Unit
Conversion period + one CPU Unit cycle
Disconnection detection Detects disconnections at each input and turns ON the Disconnection Detection Flag.
Hardware detection time: Approx. 0.5 s max.
The process value overrange direction for when a disconnection occurs can be specified. (High: 115%
of set input range; low: -15% of set input range)
Function Mean value
processing
(input filter)
Calculates the moving average for the specified number of process values (1 to 128), and stores that
value in the CIO Area as the process value.
Process value alarm Process value 4-point alarm (LL, L, H, HH), alarm hysteresis, and ON-delay timer (0 to 60 s) are
available.
Rate-of-change
calculation
Calculates the amount of change per comparison time interval (1 to 16 s).
Rate-of-change
alarm
Rate-of-change 2-point alarm (L, H), alarm hysteresis (shared with process value alarm), and ON-
delay timer (0 to 60 s, shared with process value alarm) are available.
Adjustment period
control
When zero/span adjustment is executed, the date is internally recorded at the Unit. When the preset
zero/span adjustment period and number of days notice have elapsed (allocated in Expansion Setting
Area), this function turns ON a warning flag to give notice that it is time for readjustment.
Peak and bottom
detection
This function detects the maximum (peak) and minimum (bottom) analog input values, from when the
Hold Start Bit (output) allocated to the Expansion Control/Monitor Area turns ON until it turns OFF,
and stores them in the Expansion Control/Monitor Area.
Top and valley
detection
This function detects the top and valley values for analog inputs, from when the Hold Start Bit
(output) allocated to the Expansion Control/Monitor Area turns ON until it turns OFF, and stores
them in the Expansion Control/Monitor Area.
Isolation Between inputs and Controller signals, and between inputs: Isolation by transformer for power supply,
and by photocoupler for signals.
Cold junction compensation circuit: No isolation from input 2
Insulation resistance 20 MΩ (at 500 V DC) between inputs
Dielectric strength Between inputs: 1,000 V AC, at 50/60 Hz, for 1 min, leakage current 10 mA max.
External connections Terminal block (detachable)
Unit number settings Set by rotary switches on front panel, from 0 to 95.
Indicators Four LED indicators on front panel (for normal operation, errors detected at the Thermocouple Input
Unit, errors related to the CPU Unit, and use of external power supply).
Front panel connector Sensor input connector terminal block (detachable)
Effect on CPU Unit cycle time 0.3 ms
Current consumption 5 V DC at 180 mA max.
External power supply 24 VDC +10%/-15% 60 mA max., inrush current: 20 A for 1 ms max.
(The external 24-VDC power supply must be isolated.)
Dimensions 31 × 90 × 65 mm (W × H × D)
Weight 150 g max.
Standard accessories Two cold junction sensors (installed in terminal block)

* The method for calculating the error in temperature measurements, including the temperature coefficient, is given
   below. The "full scale of electromotive force" is the difference between the high limit and low limit converted to
   electromotive force for each thermocouple.

CJ1W-PTS Specifications 2

CJ1W-PTS51 Isolated-type Thermocouple Input Unit

Item Specifications
Model CJ1W-PTS51
Applicable Controller CJ Series
Unit classification CJ-series Special I/O Unit
Mounting position CJ-series CPU Rack or CJ-series Expansion Rack
Maximum number of Units 40 (within the allowable current consumption and power consumption range)
Unit numbers 00 to 95 (Cannot duplicate Special I/O Unit numbers.)
Areas for
data
exchange
with CPU
Unit
Special I/O Unit Area
(Operation Data)
10 words/Unit
Thermocouple Input Unit to CPU Unit:
All process values, process value alarms (L, H), conversion data enabled flag, sensor errors, cold
junction sensor errors
DM Area words
allocated to Special
I/O Units
(Setting parameter)
100 words/Unit
CPU Unit to Thermocouple Input Unit:
Temperature sensor type, input range (same for all I/O), process value alarm setting (L, H), zero/span
adjustment value.
Number of temperature sensor
inputs
4
Temperature sensor types Selectable from K, J, L, R, S, T, B. (Same setting for all inputs.)
Data storage in the CIO Area The actual process data in the input range is stored in four digits hexadecimal (binary or BCD values)
in the allocated words in the CIO Area.
Accuracy (25°C) With Celsius selected: ±0.3% of PV or ±1°C, whichever is greater, ±1 digit max.
With fahrenheit selected: ±0.3% of PV or ±2°F, whichever is greater, ±1 digit max.
However, the accuracy of K and T at -100°C or lower and L is ±2°C ±1 digit max.
The accuracy of R and S at 200°C or lower is ±3°C ± 1 digit max.
The accuracy of B at 400°C or lower is not specified.
PV: Process value data
Temperature characteristics Refer to Temperature Characteristics According to Thermocouple Type on Data Sheet.
Warmup time 30 min
Conversion period 250 ms/4 inputs
Maximum time to store data in
CPU Unit
Conversion period + one CPU Unit cycle
Sensor error detection Input Types Other Than B:
A Sensor error is detected and the Sensor Error Flag is turned ON if the upper or lower limit of the
set input range is exceeded by 20°C or 20°F. The process value overrange direction when a
Sensor error occurs can be specified (high: set input range +20°C or +20°F, low: set input range
-20°C or -20°F).
B Input Type:
A Sensor error is detected and the Sensor Error Flag is turned ON if the upper limit of 1,820°C or
3,220°F or the lower limit of 0°C or 0°F is exceeded. The process value overrange direction
when a Sensor error occurs can be specified (high: set input range 1,820°C or 3,220°F, low: set
input range 0°C or 0°F).
Function Process value alarm Process value 2-point alarm (HH, H, LL, L), alarm hysteresis, and ON-delay timer (0 to 60 s) are
available.
External alarm outputs: One per input (H or L).
External alarm
outputs
NPN outputs (with short-circuit protection)
External power supply voltage: 20.4 to 26.4 V DC
Max. switching capacity: 100 mA (for one output)
Leakage current: 0.3 mA max.
Residual voltage: 3 V max.
Isolation Between inputs and Controller signal: Transformer for power supply and photocoupler for signals
Between each input: Transformer for power supply and photocoupler for signals.
Insulation resistance 20 MΩ max. (at 500 V DC).
Between all output and NC terminals and external AC terminals (Power Supply Unit)
Between all input terminals and external AC terminals (Power Supply Unit)
Between all input terminals and all output terminals
Between all external DC terminals (input, output, and NC terminals) and FG plate
Between all input and output terminals and all NC terminals
Dielectric strength Between all output and NC terminals and external AC terminals (Power Supply Unit)
2,000 VAC, 50/60 Hz 1 min., detection current: 1 mA
Between all input terminals and external AC terminals (Power Supply Unit)
Between all input terminals and all output terminals
Between all external DC terminals (input, output, and NC terminals) and FG plate
1,000 VAC, 50/60 Hz 1 min., detection current: 1 mA
Between all channels
500 VAC, 50/60 Hz 1 min., detection current: 1mA
External connections Terminal block (detachable)
Unit number settings Set by rotary switches on front panel, from 0 to 95.
Indicators Seven LED indicators on front panel (for normal operation, errors detected at the Thermocouple
Input Unit, errors related to the CPU Unit, and four indicators for external alarm outputs.)
Current consumption (supplied
from Power Supply Unit)
5 V DC at 250 mA max.
Dimensions 31 × 90 × 65 mm (W × H × D)
Weight 150 g max.

CJ1W-PTS52 Isolated-type Resistance Thermometer Input Unit (Pt100, JPt100)

Item Specifications
Model CJ1W-PTS52
Applicable Controller CJ Series
Unit classification CJ-series Special I/O Unit
Mounting position CJ-series CPU Rack or CJ-series Expansion Rack
Maximum number of Units 40 (within the allowable current consumption and power consumption range)
Unit numbers 00 to 95 (Cannot duplicate Special I/O Unit numbers.)
Areas for
data
exchange
with CPU
Unit
Special I/O Unit Area
(Operation Data)
10 words/Unit
Resistance Thermometer Input Unit to CPU Unit:
All process values, process value alarms (L, H), conversion data enabled flags, sensor errors.
DM Area words
allocated to Special
I/O Units
(Setting parameter)
100 words/Unit
CPU Unit to Resistance Thermometer Input Unit:
Temperature sensor type, input range (user set), process value alarm setting (L, H), zero/span
adjustment value.
Number of temperature sensor
inputs
4
Temperature sensor type Pt100 (JIS, IEC), JPt100
Sensor type, input range, and scaling to industrial units are the same for all I/O.
Data storage in the CIO Area The actual process data in the input range is stored in four digits hexadecimal (binary or BCD values)
in the allocated words in the CIO Area.
Accuracy (25 ° C) ± 0.3% of PV or ± 0.8°C, whichever is greater, ± 1 digit max.
± 0.3% of PV or ± 1.6°F, whichever is greater, ± 1 digit max.
PV: Process value data
Temperature characteristics Refer to Temperature Characteristics According to Platinum Resistance Thermometer Type on Data
Sheet.
Sensing method 3-wire method
Influence of conductor
resistance
0.4°C/Ω max.
Warmup time 10 min
Conversion period 250 ms/4 inputs
Maximum time to store data in
CPU Unit
Conversion period + one CPU Unit cycle
Sensor error detection Detects sensor error at each input and turns ON the Sensor error Flag.
Hardware detection time: Approx. 0.5 s max.
The process value overrange direction for when a sensor error occurs can be specified. (High: +20
digit of set input range; low: -20 digit of set input range)
Function Process value alarm Process value 2-point alarm (H, L), alarm hysteresis, and ON-delay timer (0 to 60 s are available).
External alarm
outputs
NPN outputs (with short-circuit protection)
External power supply voltage: 20.4 to 26.4 V DC
Max. switching capacity: 100 mA (for one output)
Leakage current: 0.3 mA max.
Residual voltage: 3 V max.
Isolation Between inputs and Controller signal: Transformer for power supply and photocoupler for signals
Between each input: Transformer for power supply and photocoupler for signals
Insulation resistance 20 MΩ max. (at 500 V DC).
Between all output and NC terminals and external AC terminals (Power Supply Unit)
Between all input terminals and external AC terminals (Power Supply Unit)
Between all input terminals and all output terminals
Between all external DC terminals (input, output, and NC terminals) and FG plate
Between all input and output terminals and all NC terminals
Dielectric strength Between all output and NC terminals and external AC terminals (Power Supply Unit)
2,000 V AC, 50/60 Hz 1 min., detection current: 1 mA
Between all input terminals and external AC terminals (Power Supply Unit)
Between all input terminals and all output terminals
Between all external DC terminals (input, output, and NC terminals) and FG plate
1,000 V AC, 50/60 Hz 1 min., detection current: 1 mA
Between all channels
500 VAC, 50/60 Hz 1 min., detection current: 1 mA
External connections Terminal block (detachable)
Unit number settings Set by rotary switches on front panel, from 0 to 95.
Indicators Seven LED indicators on front panel (for normal operation, errors detected at the Resistance
Thermometer Input Unit, errors detected at the CPU Unit, and four indicators for external alarm
outputs.)
Current consumption 5 V DC at 250 mA max
Dimensions 31 × 90 × 65 mm (W × H × D)
Note: The height including the Backplane is 145 mm.
Weight 150 g max.